Removal

INTERIOR: ROOF HEADLINING: REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

2. REMOVE FRONT DOOR SCUFF PLATE LH

(a) Using a screwdriver, detach the 10 claws and remove the scuff plate.





HINT
Tape the screwdriver tip before use.

3. REMOVE FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure described for the LH side.

4. REMOVE COWL SIDE TRIM BOARD LH

(a) Remove the cap nut.





(b) Using a screwdriver, detach the 3 claws and remove the trim board.

HINT
Tape the screwdriver tip before use.

5. REMOVE COWL SIDE TRIM BOARD RH

HINT
Use the same procedure described for the LH side.

6. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Remove the front door opening trim weatherstrip.

7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Remove the front door opening trim weatherstrip.

8. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY Removal

9. REMOVE COMBINATION METER ASSEMBLY Removal

10. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL CENTER Removal

11. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL CENTER Removal

12. REMOVE RADIO RECEIVER ASSEMBLY (w/o Navigation System) Removal

13. REMOVE NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System) Removal

14. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY CENTER Removal

15. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY Removal

16. REMOVE FRONT PILLAR GARNISH LH

(a) w/o Curtain Shield Airbag:





(1) Using a clip remover, detach the 2 clips.

(2) Pull the garnish in the direction indicated by the arrow in the illustration to detach the 3 claws. Then remove the garnish.

(b) w/ Curtain Shield Airbag:





(1) Detach the 2 clips.

(2) Cut off the 2 clips.

(3) Detach the 3 claws and remove the garnish.

(4) Remove the 2 clips from the vehicle body.

NOTICE:
As the clips are cut, be sure to install new clips when installing the garnish.

(c) Using a clip remover, remove the 4 wire harness clamps.





(d) w/ Curtain Shield Airbag:





(1) Completely cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) piece of cloth or nylon, and secure the cover with adhesive tape as shown in the illustration.

NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

17. REMOVE FRONT PILLAR GARNISH RH

(a) w/o Curtain Shield Airbag:





(1) Using a clip remover, detach the 2 clips.

(2) Pull the garnish in the direction indicated by the arrow in the illustration to detach the 3 claws. Then remove the garnish.

(b) w/ Curtain Shield Airbag:





(1) Detach the 2 clips.

(2) Cut off the 2 clips.

(3) Detach the 3 claws and remove the garnish.

(4) Remove the 2 clips from the vehicle body.

NOTICE:
As the clips are cut, be sure to install new clips when installing the garnish.

(5) Completely cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) piece of cloth or nylon, and secure the cover with adhesive tape as shown in the illustration.





NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

18. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY Removal

19. REMOVE REAR DOOR SCUFF PLATE LH

(a) Using a screwdriver, detach the 9 claws.





HINT
Tape the screwdriver tip before use.

(b) Using a clip remover, detach the 2 clips and remove the scuff plate.

20. REMOVE REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure described for the LH side.

21. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Remove the rear door opening trim weatherstrip.

22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Remove the rear door opening trim weatherstrip.

23. REMOVE LOWER CENTER PILLAR GARNISH LH

(a) Disconnect the front seat outer belt floor anchor.

(1) Remove the anchor cover.

(2) Remove the bolt and disconnect the floor anchor.





(b) Using a screwdriver, detach the 2 claws.





HINT
Tape the screwdriver tip before use.

(c) Using a clip remover, detach the 2 clips and remove the garnish.

24. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT
Use the same procedure described for the LH side.

25. REMOVE CENTER PILLAR GARNISH LH

(a) Remove the 2 screws.





(b) Using a clip remover, detach the clip and remove the garnish.

26. REMOVE CENTER PILLAR GARNISH RH

HINT
Use the same procedure described for the LH side.

27. REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/o Rear No. 2 Seat)

(a) Remove the package tray trim pocket.

28. REMOVE TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat)

(a) Remove tonneau cover.

29. REMOVE REAR FLOOR NO. 1 BOARD (w/o Rear No. 2 Seat)

(a) Remove the rear floor No. 1 board.

30. REMOVE DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)

(a) Remove the deck board.

31. REMOVE NO. 2 SEAT HINGE COVER LH (w/ Rear No. 2 Seat) Removal

32. REMOVE NO. 2 SEAT HINGE COVER RH (w/ Rear No. 2 Seat)

HINT
Use the same procedure described for the LH side.

33. REMOVE NO. 2 SEAT LEG COVER LH (w/ Rear No. 2 Seat) Removal

34. REMOVE NO. 2 SEAT LEG COVER RH (w/ Rear No. 2 Seat)

HINT
Use the same procedure described for the LH side.

35. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat) Removal

36. REMOVE REAR NO. 2 SEAT ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT
Use the same procedure described for the LH side.

37. REMOVE REAR FLOOR NO. 3 BOARD

(a) Remove the rear floor No. 3 board.

38. REMOVE REAR FLOOR NO. 2 BOARD

(a) Remove the rear floor No. 2 board.

39. REMOVE REAR FLOOR NO. 1 MAT SUPPORT SIDE PLATE

(a) w/o Rear No. 2 Seat:





(1) Remove the 4 screws.

(2) Using a clip remover, detach the 7 clips and remove the plate.

(b) w/ Rear No. 2 Seat:





(1) Using a clip remover, detach the 8 clips and remove the plate.

40. REMOVE BACK DOOR WEATHERSTRIP

(a) Remove the back door weatherstrip.

41. REMOVE REAR FLOOR FINISH PLATE

(a) Using a clip remover, detach the 6 clips.





(b) Detach the 6 claws and remove the finish plate.

42. REMOVE REAR DECK TRIM COVER LH (w/ Rear No. 2 Seat)





(a) Remove the bolt.

(b) Using a screwdriver, detach the 4 claws and remove the trim cover.

HINT
Tape the screwdriver tip before use.

43. REMOVE REAR DECK TRIM COVER RH (w/ Rear No. 2 Seat)

HINT
Use the same procedure described for the LH side.

44. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/o Rear No. 2 Seat) Removal

45. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL RH (w/o Rear No. 2 Seat) Removal

46. REMOVE TETHER ANCHOR BRACKET SUB-ASSEMBLY (w/o Rear No. 2 Seat)

(a) Remove the tether anchor bracket together with the bolt.





47. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (w/o Rear No. 2 Seat)

(a) Disconnect the rear No. 1 seat belt outer floor anchor.





(1) Remove the anchor cover.

(2) Remove the bolt and disconnect the floor anchor.

(b) Remove the 2 screws and 2 bolts.





(c) Using a screwdriver, detach the 5 claws.

HINT
Tape the screwdriver tip before use.

(d) Using a clip remover, detach the 4 clips and remove the deck trim side panel.

(e) Disconnect the rear power point socket connector.

(f) Remove the belt hanger.

48. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (w/ Rear No. 2 Seat)

(a) Disconnect the rear No. 1 seat belt outer floor anchor.





(1) Remove the anchor cover.

(2) Remove the bolt and disconnect the floor anchor.

(b) Disconnect the rear No. 2 seat belt outer floor anchor.

(1) Remove the bolt and disconnect the floor anchor.





(c) Remove the 2 screws and 2 bolts.





(d) Using a screwdriver, detach the 5 claws.

HINT
Tape the screwdriver tip before use.

(e) Using a clip remover, detach the 4 clips and remove the deck trim side panel.

(f) Disconnect the rear power point socket connector.

(g) Remove the belt hanger.

49. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (w/o Rear No. 2 Seat)

(a) Disconnect the rear No. 1 seat belt outer floor anchor.





(1) Remove the anchor cover.

(2) Remove the bolt and disconnect the floor anchor.

(b) Remove the 2 screws and 2 bolts.





(c) Using a screwdriver, detach the 5 claws.

HINT
Tape the screwdriver tip before use.

(d) Using a clip remover, detach the 4 clips and remove the deck trim side panel.

(e) Remove the belt hanger.

50. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (w/ Rear No. 2 Seat)

(a) Disconnect the rear No. 1 seat belt outer floor anchor.





(1) Remove the anchor cover.

(2) Remove the bolt and disconnect the floor anchor.

(b) Disconnect the rear No. 2 seat belt outer floor anchor.

(1) Remove the bolt and disconnect the floor anchor.

(c) Remove the 2 screws and 2 bolts.





(d) Using a screwdriver, detach the 5 claws.

HINT
Tape the screwdriver tip before use.

(e) Using a clip remover, detach the 4 clips and remove the deck trim side panel.

(f) Remove the belt hanger.

51. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (w/o Rear No. 2 Seat)

(a) Using a clip remover, detach the 8 clips and remove the garnish.





52. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH (w/ Rear No. 2 Seat)

(a) Disconnect the rear No. 2 seat belt outer shoulder anchor.





(1) Using a screwdriver, detach the 2 claws and open the seat belt anchor cover.

HINT
Tape the screwdriver tip before use.

(2) Remove the bolt and disconnect the shoulder anchor.

(b) Using a clip remover, detach the 8 clips and remove the garnish.





53. REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

HINT
Use the same procedure described for the LH side.

54. REMOVE REAR ROOM PARTITION NET HOOK LH

(a) Remove the 2 screws and net hook.





55. REMOVE REAR ROOM PARTITION NET HOOK RH

HINT
Use the same procedure described for the LH side.

56. REMOVE VISOR ASSEMBLY LH

(a) Using a screwdriver, detach the 4 claws and remove the visor bracket cover.





HINT
Tape the screwdriver tip before use.

(b) Detach the visor from the visor holder (A in the illustration).





(c) Detach the 2 claws and remove the visor.

57. REMOVE VISOR ASSEMBLY RH

HINT
Use the same procedure described for the LH side.

58. REMOVE VISOR HOLDER

(a) Turn the visor holder counterclockwise and pull to remove it.





59. REMOVE VANITY LIGHT ASSEMBLY Removal

60. REMOVE MAP LIGHT ASSEMBLY Removal

61. REMOVE ROOM LIGHT ASSEMBLY Removal

62. REMOVE ASSIST GRIP COVER (for Front Grip)

(a) Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.





HINT
Tape the screwdriver tip before use.

63. REMOVE ASSIST GRIP SUB-ASSEMBLY

(a) Detach the 4 claws and remove the assist grip.





64. REMOVE ASSIST GRIP COVER (for Rear Grip)

(a) Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.





HINT
Tape the screwdriver tip before use.

65. REMOVE REAR ASSIST GRIP ASSEMBLY

(a) Detach the 4 claws and remove the assist grip.





66. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER Removal

67. REMOVE SHOULDER BELT ANCHOR COVER RH Removal

68. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

(a) Remove the sun roof opening trim moulding.

69. REMOVE ROOF HEADLINING ASSEMBLY

(a) Using a screwdriver, remove the wire harness clamp.





(b) Disconnect the roof wire connector.

(c) w/o Sliding Roof:





(1) Using a clip remover, remove the 4 clips and headlining.

(d) w/ Sliding Roof:

(1) Disconnect the connector from the drive gear.

(2) Using a clip remover, remove the 2 clips and headlining.

70. REMOVE NO. 1 ROOF HEADLINING SUPPORT

(a) Remove the No. 1 roof headlining support.

71. REMOVE NO. 2 ROOF HEADLINING SUPPORT

(a) Remove the No. 2 roof headlining support.

72. REMOVE NO. 3 ROOF HEADLINING SUPPORT

(a) Remove the No. 3 roof headlining support.

73. REMOVE NO. 4 ROOF HEADLINING SUPPORT

(a) Remove the No. 4 roof headlining support.

74. REMOVE NO. 1 ROOF WIRE

HINT
Perform this procedure only when replacing the roof headlining.

(a) Remove the double-sided tape and roof wire.

75. REMOVE NO. 1 ROOF SILENCER PAD

(a) w/o Sliding Roof:

Remove the 5 silencer pads.

(b) w/ Sliding Roof:

Remove the 2 silencer pads.

76. REMOVE NO. 3 ROOF SILENCER PAD

(a) Remove the No. 3 silencer pad.