C0278

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: C0278/11: Open or Short Circuit in ABS Solenoid Relay Circuit
C0278/11 - Open or Short Circuit in ABS Solenoid Relay Circuit

DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid and TRAC solenoid.

The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by self diagnosis performed when the vehicle starts running.

The ABS solenoid relay is housed in the skid control ECU in the brake actuator assembly.





WIRING DIAGRAM

Refer to DTCs C0226/21, C0236/22, C0246/23, C0256/24, C1225/25, C1226/26, C1227/27 and C1228/28 C0226.

INSPECTION PROCEDURE

HINT
When C1241/41 is output together with C0278/11, inspect and repair the trouble areas indicated by C1241/41 first C1241.

PROCEDURE

1. INSPECT ABS NO. 2 FUSE

(a) Remove the fusible link block from the engine room relay block.





(b) Check if the fusible link is melted.

OK:

The fusible link is not melted.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration

Text in Illustration:

NG -- REPLACE FUSIBLE LINK BLOCK (ABS NO. 2 FUSE)
OK -- Continue to next step.

2. INSPECT SKID CONTROL ECU (+BS TERMINAL)

(a) Install the fusible link block to the engine room relay block.





(b) Make sure that there is no looseness at the locking part and the connecting part of the connector.

(c) Disconnect the skid control ECU connector.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





Text in Illustration

Text in Illustration:

NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)
OK -- Continue to next step.

3. INSPECT SKID CONTROL ECU (GND1 TERMINAL)

(a) Measure the resistance according to the value(s) in the table below.





Standard Resistance:





Text in Illustration

Text in Illustration:

NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK -- Continue to next step.

4. RECONFIRM DTC

HINT
This code is detected when a problem is identified in the brake actuator assembly.

The solenoid circuit is located in the brake actuator assembly.

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.

(a) Reconnect the skid control ECU connector.

(b) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.

(c) Start the engine.

(d) Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

(e) Check if the same DTC is recorded Reading and Clearing Diagnostic Trouble Codes.

Result:





HINT
* If a speed signal of 15 km/h (9 mph) or more is input to the skid control ECU, with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
* If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harnesses, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
* If any DTCs are output while jiggling a connector or wire harness of the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness.
* It is suspected that the DTCs were output due to a bad connection of the connector terminal.

B -- REPLACE BRAKE ACTUATOR ASSEMBLY Removal

A -- CHECK FOR INTERMITTENT PROBLEMS How To Proceed With Troubleshooting