Reassembly

SEAT: FRONT SEAT ASSEMBLY (for Power Seat): REASSEMBLY

REASSEMBLY

1. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side)
(a) Engage each clamp and install the front seat wire RH.
2. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) Installation
3. INSTALL SEAT POSITION SENSOR Installation
4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

(a) Engage the clamp.
(b) Connect the connector to the seat heater control sub-assembly.
5. INSTALL FRONT SEAT WIRE

(a) Engage the 5 clamps.
(b) Engage the 2 claws.
(c) Connect the 3 connectors.
(d) w/ Seat Heater System:

(1) Connect the 3 connectors.
(2) Engage the 4 clamps.

(e) Connect the connector.
(f) Engage the 2 clamps and install the front seat wire.
6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

(a) Engage the guide.
(b) Engage the hook as shown in the illustration.
(c) Install the front seat lower cushion shield LH with the screw.

Text in Illustration

7. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

(a) Engage the guide.
(b) Engage the hook as shown in the illustration.
(c) Install the front seat lower cushion shield RH with the screw.

Text in Illustration

8. INSTALL RECLINING ADJUSTER INSIDE COVER LH

(a) Engage the guide.
(b) Install the reclining adjuster inside cover LH with the screw.
9. INSTALL SEAT RECLINING ADJUSTER INSIDE COVER LH

(a) Engage the guide.
(b) Engage the clamp.
(c) Install the seat reclining adjuster inside cover LH with the 2 screws.

Text in Illustration

10. INSTALL RECLINING ADJUSTER INSIDE COVER RH

(a) Engage the guide.
(b) Install the reclining adjuster inside cover RH with the screw.
11. INSTALL SEAT RECLINING ADJUSTER INSIDE COVER RH

(a) Engage the guide.
(b) Engage the clamp.
(c) Install the seat reclining adjuster inside cover RH with the 2 screws.

Text in Illustration

12. INSTALL ACTIVE HEADREST LOWER UNIT

(a) Install the active headrest lower unit with the 2 nuts.
Torque: 5.0 Nm (51 kgf-cm, 44in-lbf)
13. INSTALL ACTIVE HEADREST UPPER UNIT

(a) Install the active headrest upper unit with the 4 nuts.
Torque: 14 Nm (143 kgf-cm, 10ft-lbf)
(b) Connect the cable to the active headrest upper unit with the nut as shown in the illustration.
Torque: 5.0 Nm (51 kgf-cm, 44in-lbf)
14. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY

(a) Install the bush.

(b) Install the lumbar support adjuster assembly with the guide and 2 screws.
(c) Connect the connector.

(d) Install the front seatback spring sub-assembly with the 8 guides and a new clamp.

Text in Illustration

15. INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

(a) Using a tacker, install the front seatback heater to the end of the seat cover with 12 new tack pins.
NOTICE: Be careful not to damage the cushion.

16. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

(a) Using hog ring pliers, install the separate type front seatback cover with 10 new hog rings.

Text in Illustration

NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.

17. INSTALL FRONT SEATBACK COVER WITH PAD
(a) Temporarily install the front seatback cover with pad to the front seat frame assembly with adjuster.

(b) Engage the 4 claws and install the 2 front seat headrest supports.

NOTICE: Be careful not to damage the cover.

(d) Using hog ring pliers, install the front seatback cover with pad with 2 new hog rings.

Text in Illustration

NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.

(e) Engage the 4 hooks.

(f) Install the front seatback cover bracket with the guide and nut.

Text in Illustration

Torque: 5.5 Nm (56 kgf-cm, 49in-lbf)

NOTICE:
- For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
- Check that the strap is not twisted after installing the bracket.
- Install the bracket securely.

18. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY

(a) Engage the 2 guides as shown in the illustration.

(b) Engage the 14 claws.

(c) Install the front seatback board sub-assembly with the 2 screws.
19. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

(a) Using a tacker, install the front seat cushion heater to the end of the seat cover with 25 new tack pins.

NOTICE:
- Be careful not to damage the cushion.
- When installing the tack pins, take care to minimize wrinkles as much as possible.

20. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

(a) Using hog ring pliers, temporarily install the separate type front seat cushion cover with 18 new hog rings.

Text in Illustration

NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, take care to minimize wrinkles as much as possible.

21. INSTALL FRONT SEAT CUSHION COVER WITH PAD

(a) Temporarily install the front seat cushion cover with pad to the front seat frame assembly with adjuster.
(b) Engage each hook as shown in the illustration.

(1) Engage each clamp.
(d) w/ Seat Heater System:

(1) Connect the connector.
(2) Engage each clamp.

(e) Engage the 4 hooks and install the front seat cushion cover with pad.

(f) Install the 2 hooks as shown in the illustration.
22. INSTALL FRONT SEAT CUSHION INNER SHIELD

(a) Engage the guide and temporarily install the front seat cushion inner shield as shown in the illustration.

(b) Engage the claw.
(c) Install the front seat cushion inner shield with the screw.
23. INSTALL FRONT SEAT INNER BELT ASSEMBLY Installation
24. INSTALL POWER SEAT SWITCH

(a) Connect the connector.
(b) Install the power seat switch with the 3 screws.
25. INSTALL FRONT POWER SEAT LUMBAR SWITCH

(a) Install the front power seat lumbar switch with the 2 screws.
26. INSTALL FRONT SEAT CUSHION SHIELD

(a) Engage the 2 claws.
(b) Install the front seat cushion shield with the screw.
27. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY

(a) Connect the connector to the front power seat lumbar switch.

(b) Engage the guide and claw.
(c) Install the front seat cushion shield assembly with the 5 screws.

(d) Engage the 2 hooks.
28. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

(a) Engage the 4 claws and install the slide and vertical power seat switch knob.
29. INSTALL RECLINING POWER SEAT SWITCH KNOB

(a) Engage the 4 claws and install the reclining power seat switch knob.