Reassembly
U660F AUTOMATIC TRANSMISSION / TRANSAXLE: DIFFERENTIAL CASE: REASSEMBLY
1. INSTALL DIFFERENTIAL SIDE GEAR
(a) Coat the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers with ATF and install them to the differential case.
2. INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT
(a) Coat the front No. 1 differential pinion shaft with ATF, and install it to the differential case.
3. INSPECT DIFFERENTIAL SIDE GEAR BACKLASH Differential Case
4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN
(a) Using a pin punch (3 mm) and hammer, install the pinion shaft straight pin.
NOTICE:
Align the holes, and install the pinion shaft straight pin.
(b) Using a chisel and hammer, stake the differential case.
NOTICE:
Stake the differential case after adjusting the backlash.
5. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
(a) Using SST and a press, install a new front differential case rear tapered roller bearing to the differential case.
SST : 09710-04081
SST : 09950-60010
09951-00480
SST : 09950-70010
09951-07100
NOTICE:
Do not damage the bearing cage during bearing inner race installation.
(b) Using SST and a hammer, install a new front differential case rear tapered roller bearing outer race to the transaxle case.
SST : 09950-60020
09951-00890
SST : 09950-70010
09951-07150
NOTICE:
Ensure that there is no clearance between the bearing and transaxle case.
6. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
(a) Using SST and a press, install a new front differential case front tapered roller bearing to the differential case.
SST : 09316-12010
SST : 09649-17010
SST : 09950-70010
09951-07100
NOTICE:
Do not damage the bearing cage during bearing inner race installation.
(b) Install the shim to the transaxle housing.
(c) Using SST and a hammer, install a new front differential case front tapered roller bearing outer race to the transaxle housing.
SST : 09950-60010
09951-00910
SST : 09950-70010
09951-07150
NOTICE:
Ensure that there is no clearance between the bearing and transaxle housing.
7. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD
(a) Install the differential assembly to the transaxle case.
(b) Clean the contact surfaces of the transaxle case and transaxle housing.
(c) Install the transaxle housing to the transaxle case with the 20 bolts.
Bolt A - Torque : 31 Nm (316 kgf-cm, 23 ft-lbf)
Bolt B - Torque : 23 Nm (234 kgf-cm, 17 ft-lbf)
(d) Using SST, turn the differential assembly right and left 2 or 3 times to settle the bearing.
SST : 09564-33010
(e) Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.
SST : 09564-33010
Turning torque:
1.1 to 1.9 N*m (11 to 19 kgf*cm, 10 to 17 in.*lbf)
(f) If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.
Shim Thickness: mm (in.):
(g) Remove the 20 bolts and the transaxle housing from the transaxle case.
(h) Remove the differential assembly from the transaxle case.
8. INSTALL FRONT DIFFERENTIAL RING GEAR
(a) Using ATF and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).
NOTICE:
Do not heat the ring gear to more than 110°C (230°F).
(b) Clean the contact surface of the front differential case.
(c) Align the matchmarks, and install the front differential ring gear case quickly.
Text in Illustration:
NOTICE:
Do not install the bolts while the ring gear is hot.
(d) Install and tighten the 12 bolts.
Torque : 120 Nm (1223 kgf-cm, 88 ft-lbf)
NOTICE:
Tighten the bolts a little at a time in a diagonal sequence.
9. INSTALL TRANSAXLE CASE OIL SEAL
(a) Coat the lip of a new oil seal with MP grease.
(b) Using SST and a hammer, install the oil seal.
SST : 09316-10010
SST : 09950-70010
09951-07100
Oil seal driven in depth:
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
NOTICE:
Check that the oil seal is installed in the correct direction.
10. INSTALL FRONT TRANSAXLE CASE OIL SEAL
(a) Inside:
(1) Coat the lip of a new front transaxle case oil seal with MP grease.
(2) Using SST and a hammer, tap in the front transaxle case oil seal.
SST : 09950-60010
09951-00410
SST : 09950-70010
09951-07200
Oil seal driven in depth:
21.5 to 22.5 mm (0.846 to 0.886 in.)
(b) Outside:
(1) Coat the lip of a new front transaxle case oil seal with MP grease.
(2) Using SST and a hammer, tap in the front transaxle case oil seal.
SST : 09649-17010
SST : 09950-70010
09951-07200
Oil seal driven in depth:
5.5 to 6.5 mm (0.217 to 0.256 in.)
NOTICE:
Check that the oil seal is installed in the correct direction.