Checking the Shift Lock
Checking the shift lock
Checking fuses
- Ignition off.
Check that fuse 11C/24 (10A) is intact.
Replace the fuse if it is damaged.
Other information
- For further information about the fuses and relays, see the Wiring Diagram.
Is the fuse intact?
Yes - Checking the ground lead
No - Checking the cable
-------------------------------------------------
Checking the ground lead
- Ignition off
- Remove connector from Shift Lock module 3/156.
Check the cable between Shift Lock connector terminal #6 and ground terminal 31/6. Check for an open-circuit.
Remedy as necessary.
Other information:
- To connect the breakout box, see Connecting the breakout box Connecting the Breakout Box, Central Electronic Module (CEM)
- Checking wiring and terminals Checking Wiring And Terminals.
Is the cable OK?
Yes - Checking the power supply
No - FAULT FOUND
-------------------------------------------------
Checking the power supply
- Ignition off
- Remove relay 2/29 from the central electronic module (CEM) relay holder
- Ignition on.
Check the voltage between relay holder 2/29 terminal #3 and ground.
Other information:
- To connect the breakout box, see Connecting the breakout box Connecting the Breakout Box, Central Electronic Module (CEM)
- For information about signals, see Signal specification Signal Specification.
Is the voltage OK?
Yes - Checking the relay
No - Repair cable
-------------------------------------------------
Repair cable
- Ignition off
- Remove relay 2/29 from the central electronic module (CEM) relay holder.
Repair the cable between fuse 11C/24 terminal #2 (10A) and relay holder 2/29 terminal #3. Check for an open-circuit.
Other information:
- To connect the breakout box, see Connecting the breakout box Connecting the Breakout Box, Central Electronic Module (CEM)
- For information about signals, see Signal specification Signal Specification
- Checking wiring and terminals Checking Wiring And Terminals.
Continue - FAULT FOUND
-------------------------------------------------
Checking the cable
- Ignition off
- Remove relay 2/29 from the central electronic module (CEM) relay holder.
Check the cable between fuse 11C/24 terminal #2 (10A) and relay holder 2/29 terminal #3. Check for a short-circuit to ground.
Remedy as necessary.
Other information:
- To connect the breakout box, see Connecting the breakout box Connecting the Breakout Box, Central Electronic Module (CEM)
- For information about signals, see Signal specification Signal Specification
- Checking wiring and terminals Checking Wiring And Terminals.
Is the cable correct?
Yes - Checking the signal cable
No - FAULT FOUND
-------------------------------------------------
Checking the relay
Check that relay 2/29 is correctly installed.
Check the relay terminals.
Remedy as necessary.
Is the relay OK?
Yes - Checking the cable
No - FAULT FOUND
-------------------------------------------------
Checking the signal cable
- Ignition off.
Check the cable between relay holder 2/29 terminal #1 and Shift Lock connector terminal #1. Check for a short-circuit to ground.
Remedy as necessary.
Other information:
- To connect the breakout box, see Connecting the breakout box Connecting the Breakout Box, Central Electronic Module (CEM)
- For information about signals, see Signal specification Signal Specification
- Checking wiring and terminals Checking Wiring And Terminals.
Is the cable correct?
Yes - Checking the cable
No - FAULT FOUND
-------------------------------------------------
Checking the cable
- Ignition off.
Check the cable between relay holder 2/29 terminal #1 and Shift Lock connector 3/156 terminal #1. Check for an open-circuit.
Remedy as necessary.
Other information:
- To connect the breakout box, see Connecting the breakout box Connecting the Breakout Box, Central Electronic Module (CEM)
- For information about signals, see Signal specification Signal Specification
- Checking wiring and terminals Checking Wiring And Terminals.
Is the cable correct?
Yes - Checking the cable
No - FAULT FOUND
-------------------------------------------------
Checking the cable
- Ignition off
- Remove relay 2/29 from the central electronic module (CEM).
Check the cable between fuse 11C/24 terminal #2 (10A) and relay holder 2/29 terminal #3. Check for an intermittent short-circuit to ground.
Also check the cable between relay holder 2/29 terminal #1 and Shift Lock connector terminal #1. Check for a short-circuit to ground.
Remedy as necessary.
Other information:
- To connect the breakout box, see Connecting the breakout box Connecting the Breakout Box, Central Electronic Module (CEM)
- For information about signals, see Signal specification Signal Specification
- Checking wiring and terminals Checking Wiring And Terminals.
Continue - FAULT FOUND
-------------------------------------------------
Checking the cable
- Ignition off.
Check the cable between fuse 11C/24 terminal #2 (10A) and relay holder 2/29 terminal #3. Check for an intermittent open-circuit.
Also check the cable between relay holder 2/29 terminal #1 and Shift Lock connector terminal #1. Check for an open-circuit.
Remedy as necessary.
Other information:
- To connect the breakout box, see Connecting the breakout box Connecting the Breakout Box, Central Electronic Module (CEM)
- For information about signals, see Signal specification Signal Specification
- Checking wiring and terminals Checking Wiring And Terminals
Continue - FAULT FOUND
-------------------------------------------------