Symptoms - Engine Controls

Symptoms - Engine Controls

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.

* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provide an overview of each diagnostic category.

Symptoms Description

Symptoms cover conditions that are not covered DTCs. Certain conditions can cause multiple symptoms. These conditions are listed together under Symptoms Testing. Conditions that may only cause certain symptoms are listed separately under Additional Symptoms Test. Perform the Symptoms Testing before using the Additional Symptoms Tests. Poor Fuel Fill Quality test may be performed separately from the Symptoms Testing and Additional Symptoms Tests procedures.

Symptoms Definition

Backfire
- Fuel ignites in the intake manifold or in the exhaust system, making a loud popping noise.

Cuts Out, Misses
- A steady pulsation or jerking that follows engine speed, which is usually more pronounced as the engine load increases. This condition is not normally felt above 1500 RPM or 48 km/h (30 mph). The exhaust has a steady spitting sound at idle or at low speed.

Detonation/Spark Knock
- A mild to severe ping which usually occurs worse while under acceleration. The engine makes sharp metallic knocks that change with throttle opening.

Dieseling, Run-On
- The engine continues to run after the key is turned OFF, but runs very rough.

Hard Start
- Engine cranks OK, but does not start for a long time. The vehicle does eventually run, or may start but immediately stalls.

Hesitation, Sag, Stumble
- Momentary lack of response as the accelerator is pushed down. This condition can occur at any vehicle speed. This condition is usually more pronounced when first trying to make the vehicle move, as from a stop. This condition may cause the engine to stall in severe conditions.

Lack of Power, Sluggishness, or Sponginess
- The engine delivers less than expected power. Little or no increase in speed when the accelerator pedal is pushed down part way.

Poor Fuel Economy
- Fuel economy, as measured by an actual road test, is noticeably lower than expected. Also, the fuel economy is noticeably lower than it was on this vehicle at one time, as previously shown by an actual road test.

Poor Fuel Fill Quality
- Difficulty when refueling the vehicle.

Rough, Unstable, or Incorrect Idle and Stalling
- The engine runs unevenly at idle. If severe, the engine or the vehicle may shake. Engine idle may vary in speed. Either condition may be severe enough to stall the engine.

Surges/Chuggles
- Engine power variation under steady throttle or cruise. Feels like the vehicle speeds up and slows down with no change in the accelerator pedal position.

Symptoms Verification

Before using the Symptom tables, perform the following inspections:

* Ensure that the engine control module (ECM) and malfunction indicator lamp (MIL) are operating correctly.

* Ensure that there are no DTCs that are stored.

* Ensure that the scan tool data is within a normal operating range.

* Verify the customer concern.

* Perform the Visual/Physical Inspection in this section. The visual/physical inspection is extremely important, and can lead to correcting a condition without additional testing. It may also help reveal the cause of an intermittent condition.

Identifying Intermittent Conditions

Many intermittent conditions occur with harness or connector movement due to engine torque, rough pavement, vibration or physical movements of a component. Refer to the following for a list of issues that may cause an intermittent condition:

* Moisture and water intrusion in connectors, terminals, and components

* Incomplete connector mating

* Poor terminal contact

* High circuit or component resistance-High resistance can include any resistance, regardless of the amount, which can interrupt the operation of the component.

* Harness that is too short or tight.

* Wire insulation that is chaffed or cut.

* High or low ambient temperature

* High or low engine coolant temperatures

* High underhood temperatures

* Heat build up in component or circuit due to circuit resistance, poor terminal contact, or high electrical load

* High or low system voltage

* High vehicle load conditions

* Rough road surfaces

* Electro-magnetic interference (EMI)/circuit interference from relays, solenoids or other electrical surge

* Incorrect installation of aftermarket, add on accessories

Visual/Physical Check

* Ensure that the control module grounds are clean, tight, and correctly located. Refer to Wiring Repairs Wiring Repairs.

* Ensure that the vacuum hoses are not split, kinked, and properly connected, as shown on the Vehicle Emission Control Information label.

* Ensure that the air filter is clean and free from restrictions.

* Ensure that there is no water intrusion in connectors terminals and components.

* Inspect the air intake ducts for the following conditions:

- Collapsed

- Damaged areas

- Looseness

- Incorrect installation

- Leaking

* Inspect for air leaks at the throttle body mounting area, the mass air flow (MAF) sensor and intake manifold sealing surfaces.

* Inspect the wiring harness for the following conditions:

- Poor connections

- Pinches

- Cuts

* Inspect for loose, damaged, unseated, or missing sensors/components.

* Inspect the terminals for corrosion and correct contact.

Symptoms Testing

Backfire, Cuts Out/Misses, Detonation/Spark Knock, Dieseling/Run-On, Hard Start, Hesitation/Sag/Stumble, Lack of Power/Sluggishness/Sponginess, Poor Fuel Economy, Rough, Unstable, or Incorrect Idle and Stalling, or Surges/Chuggles

1. Test for the following conditions:

* The fuel system for the following:

- Correct fuel pressure-Refer to Fuel System Diagnosis Fuel System Diagnosis.

- Fuel injectors that are leaking or improper operation-Refer to Fuel Injector Diagnosis (CH 47976) Fuel System DiagnosisFuel Injector Diagnosis (J 39021 or Tech 2) Fuel System Diagnosis.

- Contaminated or a poor fuel quality condition-Refer to Alcohol/Contaminants-in-Fuel Diagnosis Testing and Inspection.

* The ignition system for the following:

- Spark plugs for incorrect heat range or an abnormal condition-Refer to Spark Plug Inspection Testing and Inspection.

- For diagnosis of coolant or oil fouled spark plugs, refer to Loss of Coolant Loss of Coolant or Symptoms - Engine Mechanical Symptoms - Engine Mechanical.

- Wet down the secondary ignition system with water from a spray bottle. Wetting down the secondary ignition system may help locate damaged or deteriorated components. Look/listen for arcing or misfiring as the water is applied.

- Weak spark using the J 26792 - spark tester-Refer to Electronic Ignition System Diagnosis Electronic Ignition (EI) System Diagnosis.

* The operation of the transmission torque converter clutch (TCC)-The scan tool should indicate an engine speed drop when the TCC is commanded ON.

* The operation of the A/C compressor

* Items that can cause an engine to run rich or lean.

* Inspect the heated oxygen sensors (HO2S). The HO2S should respond quickly to different throttle positions.

Caution: Refer to Heated Oxygen and Oxygen Sensor Caution Heated Oxygen and Oxygen Sensor Caution.

* Water intrusion in the HO2S connector

* The cylinder deactivation system. Refer to Cylinder Deactivation (Active Fuel Management) System Diagnosis Cylinder Deactivation (Active Fuel Management) System Diagnosis.

Note: The embossed arrows on the MAF sensor indicate the direction of the intake air flow. The arrows must point toward the engine.

* Inspect the MAF sensor installation. A MAF sensor that is incorrectly installed may cause a hard start. Install the MAF in the proper direction. Refer to Mass Airflow Sensor with Intake Air Temperature Sensor Replacement Service and Repair.

* Inspect the MAF sensor connections.

* Engine oil contaminated by fuel

* The engine for the following mechanical failures-Refer to Symptoms - Engine Mechanical Symptoms - Engine Mechanical :

- Excessive oil in the combustion chamber or leaking valve seals

- Incorrect cylinder compression

- Sticking or leaking valves

- Worn camshaft lobes

- Incorrect valve timing

- Worn rocker arms

- Broken valve springs

- Excessive carbon buildup in the combustion chambers-Clean the chambers with top engine cleaner. Follow the instructions on the can.

- Incorrect engine parts

* Vacuum hoses for splits or kinks-Verify that the routing and connections are as shown on the Vehicle Emission Control Information label.

* Knock sensor (KS) system for excessive spark retard activity-Refer to DTC P0324, P0325, P0326, P0327, P0328, P0330, P0332, or P0333 P0324.

* The exhaust system components for the following:

- Physical damage or possible internal failure

- The three-way catalytic converters for a restriction
For more information, refer to Symptoms - Engine Exhaust Symptoms - Engine Exhaust.

* Electromagnetic interference (EMI) on the reference circuit can cause a misfire condition. You can usually detect EMI with a scan tool by monitoring the engine speed parameter. A sudden increase in the engine speed parameter with little change in actual engine speed indicates that EMI is present. Inspect the high voltage components near the ignition control circuit if a condition exists.

* The crankcase ventilation valve for proper operation-Refer to Crankcase Ventilation System Inspection/Diagnosis Testing and Inspection.

* Evaporative emission (EVAP) canister purge solenoid that is stuck open

* The engine cooling system for the following conditions:

- The thermostat is the correct heat range. Refer to Thermostat Diagnosis Thermostat Diagnosis.

- Proper engine coolant level-Refer to Cooling System Draining and Filling (Vac-N-Fill Gasoline) Cooling System Draining and Filling (Vac-N-Fill)Cooling System Draining and Filling (Static Fill) Cooling System Draining and Filling (Static Fill)Cooling System Draining and Filling (Static Fill LGH, LML) Cooling System Draining and Filling (Static Fill)Cooling System Draining and Filling (Vac-N-Fill Diesel) Cooling System Draining and Filling (Vac-N-Fill).

2. If the above conditions do not address the symptom, refer to the additional symptoms tests.

Additional Symptoms Tests

Detonation/Spark Knock
- Test the engine for an overheating condition. Refer to Symptoms - Engine Cooling Symptoms - Engine Cooling.

Poor Fuel Economy
- Inspect for foreign material accumulation in the throttle bore, and for carbon deposits on the throttle plate and shaft. Also inspect for throttle body tampering.

Rough, Unstable, or Incorrect Idle and Stalling
- Inspect the engine mounts.

Surges/Chuggles
- Test the heated oxygen sensors (HO2S). The HO2S should respond quickly to a change in throttle position. If the HO2S do not respond to different throttle positions, inspect for contamination from fuel, silicon, or the incorrect use of RTV sealant. The sensors may have a white powdery coating and result in a high, but false, signal voltage, which gives a rich exhaust indication. The ECM reduces the amount of fuel delivered to the engine, causing a driveability condition.

Hard Start

* Hood position switch is open

* Test the engine coolant temperature (ECT) sensor. Compare the ECT sensor value to the intake air temperature (IAT) sensor value on a cold engine. The ECT and IAT sensor values should be within ± 3°C (5°F). If the ECT sensor is out of range with the IAT sensor, test the resistance of the ECT sensor. Refer to Temperature Versus Resistance Temperature Versus Resistance for resistance specifications. Replace the ECT sensor if the resistance is not within specification. Refer to Engine Coolant Temperature Sensor Replacement Service and Repair. If the sensor is within the specification, test the ECT circuits for a high resistance.

* Test the idle air control (IAC) system.

* Test the fuel system operation. The fuel pump should turn ON for 2 seconds when the ignition is turned ON and have the correct fuel pressure. Refer to Fuel System Diagnosis Fuel System Diagnosis.

Hesitation, Sag, Stumble

* Test the manifold absolute pressure (MAP) sensor. Refer to DTC P0106 Powertrain Management.

* Test the generator. Refer to Symptoms - Engine Electrical Symptoms - Engine Electrical. Repair the charging system if the generator output voltage is less than 9 volts or more than 16 volts.

Poor Fuel Economy

* Heavy loads being carried or towed.

* Acceleration rate too much or too often.

* Inspect for foreign material accumulation in the throttle bore, and for carbon deposits on the throttle plate and shaft. Also inspect for throttle body tampering.

Poor Fuel Fill Quality

Test for the following conditions that is applicable to the current symptom.

Difficult to Fill

* Restricted vent lines

* The evaporative emission (EVAP) vent valve is stuck closed

* High fuel temperature

* A condition with the internal components of the fuel tank assembly.
For more information, refer to:

* Fuel System Description Fuel System Description

* Evaporative Emission Control System Description Description and Operation

Fuel Odor

* Saturated EVAP canister-Refer to Evaporative Emission Control System Description Description and Operation.

* A condition with the internal components of the fuel tank assembly-Refer to Fuel System Description Fuel System Description.