B1BA7

B1BA7-OCCUPANT CLASSIFICATION SYSTEM VERIFICATION REQUIRED





- When Monitored:

With the CAN ignition status as IGN_RUN, the module tries to detect potentially damaging events and monitors the CAN Bus for the Impact messages (crash event causing one or more airbag or pretensioner to deploy) or upon detecting an Offset Event (if equipped).

- Set Condition:

This DTC will set if the module detects a potentially damaging event or the Impact messages from the CAN Bus input.





Diagnostic Test

1. CHECK FOR OCCUPANT CLASSIFICATION MODULE (OCM) ACTIVE DTC:
- ACTIVE INTERNAL FAULTS
- IGNITION FAULTS
- BATTERY FAULT
- SEAT WEIGHT SENSOR DTC

NOTE: Ensure the battery is fully charged.

Turn the ignition on.

With the scan tool, read Occupant Classification Module (OCM) DTC.

Does the scan tool display any active DTC listed above?

Yes

- Diagnose and repair the DTC.

No

- Go To 2

2. VERIFY THAT DTC B1BA7-OCCUPANT CLASSIFICATION SYSTEM VERIFICATION REQUIRED IS ACTIVE

With the scan tool, read OCM DTC.

Does the scan tool display active: B1BA7-OCCUPANT CLASSIFICATION SYSTEM VERIFICATION REQUIRED?

Yes

- Go To 3

No

- Go To 5

3. PERFORM OCCUPANT CLASSIFICATION MODULE SYSTEM VERIFICATION TEST

Verify that the passenger seat is empty.

NOTE: Failure to follow the test instructions or aborting the test will cause faults to set when performing the Occupant Classification Module System Verification Test. To prevent faults due to process errors: verify that all tests steps that led you here were performed as directed; verify that the ignition is in run; Wait 30 seconds after changing the seat weight before proceeding to allow the system to stabilize; only press scan tool buttons when directed to do so; and perform the Occupant Classification Module System Verification Test to completion.

With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is complete, proceed as follows.

With the scan tool, read OCM DTC.

Does the scan tool display active: B1BA7-OCCUPANT CLASSIFICATION SYSTEM VERIFICATION REQUIRED?

Yes

- Go To 4

No - But Other DTC Present

- Diagnose and repair the DTC.

No - No Active DTC Present

- Perform *OCM SYSTEM VERIFICATION TEST. Occupant Classification Module (OCM) System Verification Test

4. PERFORM SENSOR TORQUE TEST

WARNING: To avoid serious or fatal injury, turn the ignition off, disconnect the battery and wait two minutes before proceeding.

Verify that the passenger seat is empty.

Verify that all of the Seat Weight Sensor mounting screws are tightened to torque specification.

To avoid serious or fatal injury, turn the ignition on, then reconnect the battery.

NOTE: Failure to follow the test instructions or aborting the test will cause faults to set when performing the Occupant Classification Module System Verification Test. To prevent faults due to process errors: verify that all tests steps that led you here were performed as directed; verify that the ignition is in run; Wait 30 seconds after changing the seat weight before proceeding to allow the system to stabilize; only press scan tool buttons when directed to do so; and perform the Occupant Classification Module System Verification Test to completion.

With the scan tool in OCM, select More Options, select System Tests, and select Occupant Classification Module System Verification Test. Run the test by following the instructions displayed on the scan tool. When the test is complete, proceed as follows.

With the scan tool, read OCM DTC.

Does the scan tool display active: B1BA7-OCCUPANT CLASSIFICATION SYSTEM VERIFICATION REQUIRED?

Yes

- Perform the *Diagnosis/Checkout Procedure For Seat Weight Sensors. Component Tests and General Diagnostics
- Perform *OCM SYSTEM VERIFICATION TEST. Occupant Classification Module (OCM) System Verification Test

No - But Other DTC Present

- Diagnose and repair the DTC.

No - Active DTC Present

- Perform *OCM SYSTEM VERIFICATION TEST. Occupant Classification Module (OCM) System Verification Test

5. CHECK FOR ACTIVE DTC B1BA8-OCM SYSTEM OUT OF CALIBRATION/NOT CALIBRATED

With the scan tool, read OCM DTC.

Does the scan tool display active: B1BA8-OCM SYSTEM OUT OF CALIBRATION/NOT CALIBRATED?

Yes

- Diagnose and repair the DTC.

No

- Perform *OCM SYSTEM VERIFICATION TEST. Occupant Classification Module (OCM) System Verification Test