Pinpoint Test A: The Wipers Are Inoperative - Windshield
Wipers and Washers
Pinpoint Tests
Pinpoint Test A: The Wipers are Inoperative - Windshield
Refer to Wiring Diagram Set 81, Wipers and Washers for schematic and connector information. Diagrams By Number
Normal Operation
When the ignition switch is in the RUN or ACCESSORY position, voltage is supplied to the front wiper relay coil through circuit CBP45 (YE). The front wiper relay coil is grounded at all times through circuit GD123 (BK/GY). Voltage is supplied to the front wiper relay through circuit CRW03 (VT/WH). The wiper motor is grounded through circuits GD133 (BK) and GD120 (BK/GN). The multifunction switch is grounded through circuit GD138 (BK/WH). The multifunction switch sends open and ground input signals to the wiper motor through circuits CRW17 (GN/VT), CRW18 (VT/WH), CRW19 (BU/OG) and CRW08 (VT/OG) in order to activate the wiper motor to the requested modes.
This pinpoint test is intended to diagnose the following:
- Fuse(s)
- Front wiper relay
- Wiring, terminals or connectors
- Multifunction switch
- Wiper motor
PINPOINT TEST A: THE WIPERS ARE INOPERATIVE - WINDSHIELD
NOTICE: Use the correct probe adapter(s) from the Flex Probe Kit when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
-------------------------------------------------
A1 CHECK CIRCUIT CRW03 (VT/WH) FOR VOLTAGE
- Disconnect: Wiper Motor C125 .
- Ignition ON.
- Measure the voltage between ground and wiper motor:
- C125-5, circuit CRW03 (VT/WH), harness side.
- C125-8, circuit CRW03 (VT/WH), harness side.
- Are the voltages greater than 10 volts?
Yes
GO to A6.
No
GO to A2.
-------------------------------------------------
A2 CHECK THE FRONT WIPER RELAY
- Ignition OFF.
- Disconnect: Front Wiper Relay .
- Carry out the Relay component test for the front wiper relay.
Refer to Wiring Diagrams for component testing. Diagrams By Number
- Did the front wiper relay pass the component test?
Yes
GO to A3.
No
INSTALL a new front wiper relay. TEST the system for normal operation.
-------------------------------------------------
A3 CHECK CIRCUIT CBP45 (YE) FOR VOLTAGE
- Ignition ON.
- Measure the voltage between front wiper relay socket pin 1, circuit CBP45 (YE) and ground.
- Is the voltage greater than 10 volts?
Yes
GO to A4.
No
VERIFY Smart Junction Box (SJB) fuse 45 (5A) is OK. If OK, REPAIR the circuit.
If not OK, REFER to the Wiring Diagrams to identify the possible causes of the circuit short. REPAIR the circuit. TEST the system for normal operation. Diagrams By Number
-------------------------------------------------
A4 CHECK CIRCUIT SBB50 (YE/RD) FOR VOLTAGE
- Measure the voltage between front wiper relay socket pin 3, circuit SBB50 (YE/RD) and ground.
- Is the voltage greater than 10 volts?
Yes
GO to A5.
No
VERIFY Battery Junction Box (BJB) fuse 50 (30A) is OK. If OK, REPAIR the circuit.
If not OK, REFER to the Wiring Diagrams to identify the possible causes of the circuit short. REPAIR the circuit. TEST the system for normal operation. Diagrams By Number
-------------------------------------------------
A5 CHECK CIRCUIT GD123 (BK/GY) FOR GROUND
- Measure the resistance between front wiper relay socket pin 2, circuit GD123 (BK/GY) and ground.
- Is the resistance less than 5 ohms?
Yes
REPAIR open in circuit CRW03 (VT/WH). TEST the system for normal operation.
No
REPAIR open in circuit GD123 (BK/GY). TEST the system for normal operation.
-------------------------------------------------
A6 CHECK CIRCUITS GD120 (BK/GN) AND GD133 (BK) FOR AN OPEN
- Ignition OFF.
- Measure the resistance between ground and wiper motor:
- C125-6, circuit GD120 (BK/GN), harness side.
- C125-3, circuit GD133 (BK), harness side.
- Are the resistances less than 5 ohms?
Yes
GO to A7.
No
REPAIR the circuit(s). TEST the system for normal operation.
-------------------------------------------------
A7 CHECK THE MULTIFUNCTION SWITCH
- Disconnect: Multifunction Switch C202 .
- Carry out the Multifunction Switch component test.
Refer to Wiring Diagrams for component testing. Diagrams By Number
- Did the multifunction switch pass the component test?
Yes
GO to A8.
No
INSTALL a new multifunction switch. REFER to Steering Column Switches Steering Column Multifunction Switch.
-------------------------------------------------
A8 CHECK CIRCUIT GD138 (BK/WH) FOR AN OPEN
- Measure the resistance between multifunction switch C202-15, circuit GD138 (BK/WH), harness side and ground.
- Is the resistance less than 5 ohms?
Yes
GO to A9.
No
REPAIR the circuit. TEST the system for normal operation.
-------------------------------------------------
A9 CHECK FOR CORRECT WIPER MOTOR OPERATION
- Disconnect all wiper motor connectors.
- Check for:
- corrosion.
- pushed-out pins.
- Connect all the wiper motor connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
- Is the concern still present?
Yes
INSTALL a new wiper motor. REFER to Wiper Motor - Windshield Wiper Motor - Windshield.
No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation.
-------------------------------------------------