Pinpoint Test N: The Hazard Lamps Are Inoperative/Always On
Turn Signal and Hazard Lamps
Pinpoint Test N: The Hazard Lamps Are Inoperative/Always On
Normal Operation
The Body Control Module (BCM) sends a voltage signal to the Steering Column Control Module (SCCM) for the hazard lamp function input. The signal passes through the SCCM (Steering Column Control Module) to the hazard flasher lamp switch. When the hazard flasher lamp switch is engaged, the voltage signal is routed to ground, indicating a request for the hazard lamp function. When the BCM (Body Control Module) detects a request for the hazard lamps, the BCM (Body Control Module) provides on/off voltage to all the turn lamps.
The hazard flasher lamp switch is a momentary contact switch.
- DTC B1D35:11 (Hazard Switch: Circuit Short to Ground)- a DTC that sets when the BCM (Body Control Module) detects a short to ground from the hazard lamp function input circuit.
This pinpoint test is intended to diagnose the following:
- Wiring, terminals or connectors
- Multifunction switch
- SCCM (Steering Column Control Module)
- BCM (Body Control Module)
PINPOINT TEST N : THE HAZARD LAMPS ARE INOPERATIVE/ALWAYS ON
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
N1 CHECK THE RECORDED DTCs FROM THE BCM (Body Control Module) SELF-TEST
- Check the recorded DTCs from the BCM (Body Control Module) self-test.
Is DTC B1D35:11 present?
Yes
GO to N2.
No
GO to N5.
N2 ISOLATE THE HAZARD FLASHER LAMP SWITCH AS THE CAUSE OF DTC B1D35:11
- Ignition OFF.
- Disconnect: Hazard Flasher Lamp Switch.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: BCM (Body Control Module) Self-Test.
- Repeat the BCM (Body Control Module) self-test.
Is DTC B1D35:11 still present?
Yes
GO to N3.
No
INSTALL a new hazard flasher lamp switch. TEST the system for normal operation.
N3 ISOLATE THE SCCM (Steering Column Control Module) AS THE CAUSE OF DTC B1D35:11
- Ignition OFF.
- Disconnect: SCCM (Steering Column Control Module) C2414A.
- Ignition ON.
- Enter the following diagnostic mode on the scan tool: BCM (Body Control Module) Self-Test.
- Repeat the BCM (Body Control Module) self-test.
Is DTC B1D35:11 still present?
Yes
GO to N4.
No
GO to N7.
N4 CHECK THE HAZARD LAMP REQUEST INPUT CIRCUIT FOR A SHORT TO GROUND
- Ignition OFF.
- Disconnect: BCM (Body Control Module) C2280B.
- Measure the resistance between the SCCM (Steering Column Control Module) C2414A-2, circuit CLS32 (BN/YE), harness side and ground.
Is the resistance greater than 10,000 ohms?
Yes
GO to N8.
No
REPAIR circuit CLS32 (BN/YE) for a short to ground. TEST the system for normal operation.
N5 CHECK FOR A VOLTAGE SIGNAL TO THE SCCM (Steering Column Control Module)
- Disconnect: SCCM (Steering Column Control Module) C2414A.
- Ignition OFF.
- Measure the voltage between the SCCM (Steering Column Control Module) C2414A-2, circuit CLS32 (BN/YE), harness side and ground.
Is the voltage greater than 10 volts?
Yes
INSTALL a new hazard flasher lamp switch. TEST the system for normal operation.
If the concern is still present, GO to N7.
No
GO to N6.
N6 CHECK THE HAZARD FLASHER LAMP REQUEST INPUT CIRCUIT FOR AN OPEN
- Disconnect: BCM (Body Control Module) C2280B.
- Measure the resistance between the BCM (Body Control Module) C2280B-32, circuit CLS32 (BN/YE), harness side and the SCCM (Steering Column Control Module) C2414A-2, circuit CLS32 (BN/YE), harness side.
Is the resistance less than 5 ohms?
Yes
GO to N8.
No
REPAIR circuit CLS32 (BN/YE) for an open. TEST the system for normal operation.
N7 CHECK FOR CORRECT SCCM (Steering Column Control Module) OPERATION
- Disconnect all the SCCM (Steering Column Control Module) connectors.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect all the SCCM (Steering Column Control Module) connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
Is the concern still present?
Yes
INSTALL a new SCCM (Steering Column Control Module). TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
N8 CHECK FOR CORRECT BCM (Body Control Module) OPERATION
- Disconnect all the BCM (Body Control Module) connectors.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect all the BCM (Body Control Module) connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
Is the concern still present?
Yes
INSTALL a new BCM (Body Control Module). TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.