Reassembly

SEAT: FRONT SEAT ASSEMBLY (for SIA Made Power Seat): REASSEMBLY

1. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY

(a) Engage the 4 guides to install the separate type front seatback spring assembly.

(b) Install the 4 bolts.

Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)

2. REMOVE FRONT SEAT WIRE RH (for Front Passenger Side)

(a) Connect the connectors and engage the wire harness clamps to install the front seat wire RH.

3. INSTALL FRONT NO. 2 SEAT WIRE

(a) Connect the connectors and engage the wire harness clamps to install the front No. 2 seat wire.

4. INSTALL FRONT SEAT WIRE

(a) Connect the connectors and engage the wire harness clamps to install the front seat wire.

5. INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side) Installation

6. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

(a) Engage the 2 clamps to install the seat heater control sub-assembly.

(b) Connect the connector.

7. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Driver Side)

(a) Engage the 3 claws to install the front seat cushion edge protector LH.

(b) Install the screw.

8. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Driver Side)

(a) Engage the 3 claws to install the front seat cushion edge protector RH.

(b) Install the screw.

9. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH (for Front Passenger Side)

(a) Engage the 3 claws to install the front seat cushion edge protector LH.

(b) Install the screw.

10. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH (for Front Passenger Side)

(a) Engage the 3 claws to install the front seat cushion edge protector RH.

(b) Install the screw.

11. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER LH

(a) Engage the 2 guides to install the upper reclining adjuster inside cover LH.

12. INSTALL UPPER RECLINING ADJUSTER INSIDE COVER RH

(a) Engage the 2 guides to install the upper reclining adjuster inside cover RH.

13. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)

(a) Engage the clip to install the front seat lower cushion shield LH.

(b) Engage the hook as shown in the illustration.

(c) Install the screw.

14. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)

(a) Engage the clip to install the front seat lower cushion shield RH.

(b) Engage the hook as shown in the illustration.

(c) Install the screw.

15. INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System) Installation

16. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

(a) Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 6 new hog rings.

NOTICE:
* Be careful not to damage the separate type front seatback cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

17. INSTALL FRONT SEAT AIRBAG ASSEMBLY Installation

18. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

(a) Temporarily install the separate type front seatback cover with pad.

(b) Engage the 4 claws to install the 2 front seat headrest supports.

(c) Install the 3 brackets with the 2 nuts.

Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)

CAUTION:
* For vehicles with side airbags, the separate type front seatback cover must be securely installed. Otherwise, the side airbags may not deploy properly.
* Make sure that the strap is not twisted after installing the nut.
* Install the bracket securely.
(d) Turn back the separate type front seatback cover.

(e) Using hog ring pliers, install the 2 new hog rings.

NOTICE:
* Be careful not to damage the separate type front seatback cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

(f) Using hog ring pliers, install 3 new hog rings.

NOTICE:
When installing the hog rings, take care to minimize wrinkles as much as possible.

(g) Using hog ring pliers, install 5 new hog rings.

NOTICE:
* Be careful not to damage the separate type front seatback cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

19. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System) Installation

20. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

(a) Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 16 new hog rings.

NOTICE:
* Be careful not to damage the separate type front seat cushion cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

(b) Using hog ring pliers, install 2 new hog rings.

NOTICE:
* Be careful not to damage the separate type front seat cushion cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.

21. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

(a) Temporarily install the separate type front seat cushion cover with pad.

(b) Engage each hook.

(c) w/ Seat Heater System:

(1) Engage the 2 clamps to install the seat heater wire harness.

(2) Connect the connector.

(3) Engage the clamp.

(4) Connect the connector.

(d) Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.

(e) Engage the fastener to secure the front seat airbag assembly wire harness.

22. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) Installation

23. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side) Installation

24. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side)

(a) Engage the 5 claws and 6 guides to install the front seat inner cushion shield.

25. INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)

(a) Engage the 5 claws and 7 guides to install the front seat inner cushion shield.

26. INSTALL FRONT LUMBAR POWER SEAT SWITCH (for Driver Side) Installation

27. INSTALL FRONT POWER SEAT SWITCH Installation

28. INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side)

(a) Connect the front lumbar power seat switch connector.

(b) Connect the front power seat switch connector.

(c) Engage the 2 wire harness clamps.

(d) Install the wire harness to the wire harness cover.

(e) Engage the 2 claws to close the wire harness cover.

(f) Engage the 4 claws, 7 guides and clip to install the front seat cushion shield.

29. INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side)

(a) Connect the front power seat switch connector.

(b) Engage the 2 wire harness clamps.

(c) Install the wire harness to the wire harness cover.

(d) Engage the 3 claws to close the wire harness cover.

(e) Engage the 4 claws, 8 guides and clip to install the front seat cushion shield.

30. INSTALL FRONT NO. 1 SEAT INNER CUSHION SHIELD

(a) Install the clip.

(b) Engage the 3 claws and 3 guides to install the front No. 1 seat inner cushion shield as shown in the illustration.

(d) Install the screw.

31. CONNECT SEPARATE TYPE FRONT SEATBACK COVER

(a) Connect the rubber band of the separate type front seatback cover.

32. INSTALL RECLINING POWER SEAT SWITCH KNOB

(a) Engage the 4 claws to install the reclining power seat switch knob.

33. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

(a) Engage the 4 claws to install the slide and vertical power seat switch knob.

34. INSTALL SEAT ADJUSTER COVER CAP

(a) Install the 2 seat adjuster cover caps.