Reassembly
SEAT: FRONT SEAT ASSEMBLY (for TMMK Made Power Seat): REASSEMBLY
1. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
(a) Install the separate type front seat cushion spring assembly.
2. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Driver Side) Installation
3. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY (for Front Passenger Side)
(a) Install the 2 front seatback hooks to the separate type front seatback spring assembly.
(b) Engage the 2 guides.
(c) Engage the 4 claws to install the separate type front seatback spring assembly.
4. INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY
(a) Install the front seatback frame sub-assembly with the 4 bolts.
Torque : 45 Nm (459 kgf-cm, 33 ft-lbf)
5. INSTALL FRONT SEAT CUSHION PANEL SUB-ASSEMBLY (for Driver Side)
(a) Install the front seat cushion panel sub-assembly with the 4 bolts.
Torque : 10 Nm (102 kgf-cm, 7 ft-lbf)
6. INSTALL FRONT UPPER SEAT TRACK COVER LH
(a) Engage the 2 claws to install the front upper seat track cover LH.
7. INSTALL FRONT UPPER SEAT TRACK COVER RH
(a) Engage the 2 claws to install the front upper seat track cover RH.
8. INSTALL REAR UPPER SEAT TRACK COVER LH (for Front Passenger Side)
(a) Engage the 2 claws to install the rear upper seat track cover LH.
9. INSTALL REAR UPPER SEAT TRACK COVER RH (for Front Passenger Side)
(a) Engage the 2 claws to install the rear upper seat track cover RH.
10. INSTALL FRONT NO. 2 SEAT WIRE
(a) Connect the connectors and engage the wire harness clamps to install the front No. 2 seat wire.
11. INSTALL FRONT SEAT WIRE
(a) Connect the connectors and engage the wire harness clamps to install the front seat wire.
12. INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side) Installation
13. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
(a) Engage the clamp to install the seat heater control sub-assembly.
(b) Connect the connector.
14. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)
(a) Engage the 2 claws to install the front seat lower cushion shield LH.
(b) Engage the hook as shown in the illustration.
(c) Install the screw.
Torque : 0.6 Nm (6 kgf-cm, 5 in-lbf)
15. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Driver Side)
(a) Engage the 2 claws to install the front seat lower cushion shield RH.
(b) Engage the hook as shown in the illustration.
(c) Install the screw.
Torque : 0.6 Nm (6 kgf-cm, 5 in-lbf)
16. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Front Passenger Side)
(a) Engage the 2 claws to install the front seat lower cushion shield LH.
17. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Front Passenger Side)
(a) Engage the 2 claws to install the front seat lower cushion shield RH.
18. INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System) Installation
19. INSTALL SEPARATE TYPE FRONT SEATBACK COVER
(a) Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.
NOTICE:
* Be careful not to damage the separate type front seatback cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(b) Engage the 2 fasteners.
20. INSTALL FRONT SEAT AIRBAG ASSEMBLY Installation
21. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
(a) Temporarily install the separate type front seatback cover with pad.
(b) Engage the 4 claws to install the 2 front seat headrest supports.
(c) Engage the 2 hooks.
CAUTION:
* For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
* Make sure that the strap is not twisted after engage the 2 hooks.
* Engage the 2 hooks securely.
(1) Slide each hook to engage them.
(2) Install the 4 clips.
(d) Engage the 2 fasteners.
(e) Engage the hook.
22. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System) Installation
23. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
(a) Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 12 new hog rings.
NOTICE:
* Be careful not to damage the separate type front seat cushion cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
24. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
(a) Temporarily install the separate type front seat cushion cover with pad.
(b) Engage each hook.
(c) for Driver Side:
(1) Install the separate type front seat cushion cover.
(d) for Front Passenger Side:
(1) Install the separate type front seat cushion cover.
(e) Engage the claw (D) and 3 clamps (C) to install the front seat airbag assembly wire harness.
(f) Engage the clamp (B).
(g) Connect the connector (A).
(h) w/ Seat Heater System:
(1) Connect the connector (E).
(2) Engage the clamp (F).
25. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side) Installation
26. INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side) Installation
27. INSTALL FRONT SEAT INNER CUSHION SHIELD
(a) Install the front seat inner cushion shield with the 2 screws.
Torque : 0.6 Nm (6 kgf-cm, 5 in-lbf)
28. INSTALL FRONT LUMBAR POWER SEAT SWITCH (for Driver Side) Installation
29. INSTALL FRONT POWER SEAT SWITCH Installation
30. INSTALL FRONT SEAT CUSHION SHIELD
(a) for Driver Side:
(1) Engage the 4 claws to install the front lumbar power seat switch to the front seat cushion shield.
(b) Connect the front power seat switch connector.
(c) Engage the wire harness clamp.
(d) Engage the 2 claws to install the front seat cushion shield.
(e) Install the screw.
Torque : 0.6 Nm (6 kgf-cm, 5 in-lbf)
31. CONNECT SEPARATE TYPE FRONT SEATBACK COVER
(a) Connect the 2 rubber bands of the separate type front seatback cover.
32. INSTALL RECLINING POWER SEAT SWITCH KNOB
(a) Engage the 4 claws to install the reclining power seat switch knob.
33. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
(a) Engage the 4 claws to install the slide and vertical power seat switch knob.
34. INSTALL SEAT ADJUSTER COVER CAP
(a) Install the 2 seat adjuster cover caps.