Part 3 of 5

Secondary shaft	Diameter of needle bearing contact	at 1st gear	Standard or new	39.986 - 39.999 mm
			Service limit	When worn or damaged
		at 2nd gear	Standard or new	39.986 - 39.999 mm
			Service limit	When worn or damaged
		at 3rd gear collar	Standard or new	36.975 - 36.991 mm
			Service limit	When worn or damaged
	I.D. of gears	1st gear	Standard or new	47.000 - 47.016 mm
			Service limit	When worn or damaged
		2nd gear	Standard or new	46.000 - 46.016 mm
			Service limit	When worn or damaged
		3rd gear	Standard or new	43.000 - 43.016 mm
			Service limit	When worn or damaged
	End play of gears	1st gear	Standard or new	0.07 - 0.15 mm
		2nd gear	Standard or new	0.04 - 0.12 mm
		3rd gear	Standard or new	0.10 - 0.22 mm
	37 x 58 mm thrust washer thickness	No.1	Standard or new	3.90 mm
			Service limit	When worn or damaged
		No.2	Standard or new	3.95 mm
			Service limit	When worn or damaged
		No.3	Standard or new	4.00 mm
			Service limit	When worn or damaged
		No.4	Standard or new	4.05 mm
			Service limit	When worn or damaged
		No.5	Standard or new	4.10 mm
			Service limit	When worn or damaged
		No.6	Standard or new	4.15 mm
			Service limit	When worn or damaged
	40 x 51.5 mm thrust washer thickness	No.1	Standard or new	4.80 mm
			Service limit	When worn or damaged
		No.2	Standard or new	4.85 mm
			Service limit	When worn or damaged
		No.3	Standard or new	4.90 mm
			Service limit	When worn or damaged
		No.4	Standard or new	4.95 mm
			Service limit	When worn or damaged
		No.5	Standard or new	5.00 mm
			Service limit	When worn or damaged
		No.6	Standard or new	5.05 mm
			Service limit	When worn or damaged
	3rd gear collar length		Standard or new	43.9 - 44.0 mm
	Length of 3rd gear collar flange from end		Standard or new	5.25 - 5.40 mm
			Service limit	When worn or damaged
	Sealing ring thickness		Standard or new	1.91 - 1.97 mm
			Service limit	1.86 mm
	Width of sealing ring groove		Standard or new	2.025 - 2.060 mm
			Service limit	2.080 mm
	Clutch feed pipe O.D.	3rd clutch feed pipe	Standard or new	11.47 - 11.48 mm
			Service limit	11.45 mm
		1st clutch feed pipe	Standard or new	6.97 - 6.98 mm
			Service limit	6.95 mm
	Clutch feed pipe bushing O.D.	3rd clutch feed pipe	Standard or new	11.500 - 11.518 mm
			Service limit	11.530 mm
		1st clutch feed pipe	Standard or new	7.018 - 7.030 mm
			Service limit	7.045 mm
	ATF guide of sealing rind contact I.D.		Standard or new	29.00 - 29.021 mm
			Service limit	29.05 mm
Idler gear shaft	Diameter of needle bearing contact area	End cover side	Stanard or new	32.003 - 32.013 mm
			Service limit	When worn or damaged
	Thickness of cotters		Standard or new	1.39 - 1.42 mm
Reverse idler gear	Reverse idler gear shaft diameter at needle bearing contact area		Standard or new	14.99 - 15.00 mm
			Service limit	When worn or damaged
	I.D.		Standard or new	20.007 - 20.020 mm
			Service limit	When worn or damaged
	I.D. of reverse idler gear shaft contact area on transmission housing		Standard or new	14.800 - 14.818 mm
	I.D. of reverse idler gear shaft holder		Standard or new	14.800 - 14.824 mm
			Service limit	When worn of damaged