Band Apply Servo: Service and Repair

2-4 Servo

Special Tools

J 29714-A Servo Cover Depressor


Removal Procedure





1. Remove the catalytic converter pipe. Refer to Catalytic Converter Replacement (With LU3) (Service and Repair)Catalytic Converter Replacement (With V8 Engine) (Service and Repair)Catalytic Converter Replacement (With LMM) (Service and Repair) .
2. Remove the heat shield bolts.
3. Remove the heat shield.
4. Support the transmission.
5. Remove the transmission crossmember. Refer to Transmission Support Crossmember Replacement (2WD 1500/2500) (Service and Repair)Transmission Support Crossmember Replacement (4WD 1500/2500) (Service and Repair)Transmission Support Crossmember Replacement (2WD 2500 HD/3500) (Service and Repair)Transmission Support Crossmember Replacement (4WD 2500 HD/3500) (Service and Repair) .
6. Lower the transmission with a suitable jack.




7. Remove the oil pan bolt below the servo.
8. Install the J 29714-A .
9. Tighten the bolt onJ 29714-A in order to compress the servo cover.




10. Remove the servo cover ring.
11. Remove the J 29714-A .




12. Remove the servo cover and O-ring seal. If the cover is hung up on the seal, use a pick (2) in order to pull and stretch the seal (1) out of the groove. Cut and remove the O-ring seal before removing the cover.




13. Remove the 2-4 servo.
14. Inspect the 4th apply piston, 2-4 servo converter, 2nd apply piston, and the servo piston inner housing for the following defects:

* Cracks
* Scoring
* Burrs and nicks




Installation Procedure

1. Install NEW seals onto the servo pistons and the servo cover.




2. Install the 2-4 servo.
3. Install the J 29714-A .




4. Tighten the bolt onJ 29714-A in order to compress the servo cover.
5. Install the servo cover ring.
6. Remove the J 29714-A .
Caution: Refer to Fastener Caution (Fastener Caution) .
7. Install the oil pan bolt.

Tighten the bolt to 11 Nm (97 lb in).

8. Raise the transmission.
9. Install the transmission crossmember. Refer to Transmission Support Crossmember Replacement (2WD 1500/2500) (Service and Repair)Transmission Support Crossmember Replacement (4WD 1500/2500) (Service and Repair)Transmission Support Crossmember Replacement (2WD 2500 HD/3500) (Service and Repair)Transmission Support Crossmember Replacement (4WD 2500 HD/3500) (Service and Repair) .
10. Remove the transmission jack.




11. Install the heat shield and bolts.

Tighten the bolts to 17 Nm (13 lb ft).

12. Install the catalytic converter pipe. Refer to Catalytic Converter Replacement (With LU3) (Service and Repair)Catalytic Converter Replacement (With V8 Engine) (Service and Repair)Catalytic Converter Replacement (With LMM) (Service and Repair) .
13. Fill the transmission to the proper level with DEXRON(R) VI transmission fluid. Refer to Transmission Fluid Check (4L60-E/4L65-E/4L70-E Automatic Transmission) .


Note

It is recommended that transmission adaptive pressure (TAP) information be reset.


Resetting the TAP values using a scan tool will erase all learned values in all cells. As a result, the engine control module (ECM), powertrain control module (PCM) or TCM will need to relearn TAP values. Transmission performance may be affected as new TAP values are learned.

14. Reset the TAP values. Refer to Transmission Adaptive Functions (TCM) (Transmission Adaptive Functions (TCM)) .