Operation CHARM: Car repair manuals for everyone.

Introduction To Ford Diagrams

Note
All wiring connections between components are shown exactly as they exist in the vehicles. It is important to realize, however, that no attempt has been made on the diagram to represent components and wiring as they physically appear on the vehicle. For example, a 4-foot length of wire is treated no differently in a diagram from one which is only a few inches long. Furthermore, to aid in understanding electrical (electronic) operation, wiring inside complicated components has been simplified.

Complete Circuit Operation
Each circuit is shown completely and independently in one set of diagrams. Other components which are connected to the circuit may not be shown unless they influence the circuit operation.







System Overview
Each major vehicle system includes a complete system overview diagram prior to each set of diagrams. It is important to realize that this is only a high level overview of the complete system connectivity. It includes component operational information (1), component name and base part number (2), and basic component internals (3). It does not include specific circuit information, connector or pin numbers, splices or grounds. That information is found on the subsequent diagrams in the set.


Diagram 3-3:






Current Flow (1)
Each set of diagrams normally starts with the component that powers the circuit such as a fuse or the ignition switch. Current flow is shown from the power source at the top of the diagram to ground at the bottom of the diagram. In order to concentrate on the essential parts, power supply and ground connections are sometimes simplified by a dashed line in the diagrams. A full representation of the power supply of a fuse or the power distribution from a fuse to various components is given in the Power and Ground Distribution Diagrams. Full representation of the ground connections are shown in the Power and Ground Distribution Diagrams.

Switch Positions (2)
Within the diagram, all switches, sensors and relays are shown "at rest" (as if the Ignition Switch were OFF).

Splices (3)
A dashed line indicates that the splice is not shown completely. A reference is given to the diagram where the splice appears in full.

Component Referencing (4)
Each component on a diagram has a reference to the component location view for that component (i.e. 151-1, 151-10, etc.). These view references are located to the right of each component shown in a diagram. The views themselves can be found at Vehicle Locations. Location Views

Component Names, Notes and Base Part Numbers (5)
Component names are placed on the right hand side of each component. Any notes that describe switch positions or operating conditions follow the name. Descriptions of the internals of the component are also included here. The base part number for a component is listed in parentheses next to or under a component.

Component Identification Numbers (6)
Each component on each diagram has a component identification number (i.e. A166, A205, etc.) located to the upper right hand side of the component. By finding this number or the component name on one of the A-Z Component Lists, a brief description of the component's location can be found. A-Z Components List







Fuse and Relay Information
Fuse/Locations and Relay/Locations contains a view of the fuse/relay box in which all fuses and relays are identified.







Power Distribution
Power and Ground Distribution Diagrams show the current feed circuit. The current path is shown from the battery to the ignition switch and to all fuses. It also shows the circuits protected by each fuse. The circuit is traced from the fuse to the component. All details (wires, splices, connectors) between the fuse and the first component are shown.







Ground Distribution
Power and Ground Distribution Diagrams contain the diagrams that show the complete details for each ground connection or main ground splice. This is useful in diagnosing a problem affecting several components at once (poor ground connection or ground splice). All details (wires, splices, connectors) between the ground point and the components are shown. These ground connection details are shown here in order to keep the individual set of diagrams as uncluttered as possible.







Component and Connector Information
Locations information that can be found at the vehicle level will help the user find where the various items depicted on the diagram can physically be found on the vehicle. Locations

Component Location Views show the components and their connecting wires as they can be found on the vehicle. Location Views

"Connector Views" show the views of the pins and/or cavities of all connectors. The pin and cavity sides are shown separately as if the connector were disconnected. The color of the connector housing is indicated next to the connector number when available. The harness causal number is located above the connector view and below the connector number. The circuit function charts are located below each connector. Connector Views

WARNINGS
^ Always wear safety glasses for eye protection.
^ Use safety stands whenever a procedure requires being under a vehicle.
^ Be sure that the Ignition Switch is always in the OFF position, unless otherwise required by the procedure.
^ Set the parking brake when working on any vehicle. An automatic transmission should be in PARK. A manual transmission should be in NEUTRAL.
^ Operate the engine only in a well-ventilated area to avoid danger of carbon monoxide.
^ Keep away from moving parts, especially the fan and belts, when the engine is running.
^ To prevent serious burns, avoid contact with hot metal parts such as the radiator, exhaust manifold, tailpipe, catalytic converter and muffler.
^ Do not allow flame or sparks near the battery. Gases are always present in and around the battery cell. An explosion could occur.
^ Do not smoke when working on a vehicle.
^ To avoid injury always remove rings, watches, loose hanging jewelry and avoid wearing loose clothing.