Refer to "51.Engine Control 1A.Troubleshooting(4JJ3 without DPD) Diagnostic system check-engine controls".
1) Connect the scan tool.
2) Turn OFF the ignition switch for 1 minute or more.
3) Start the engine.
4) Observe the DTC information with a scan tool. Is a DTC set?
Yes
=>Go to CMP sensor 5 V reference voltage check.
No
Go to Intermittent conditions of engine.
Refer to "202.Engine 15D.Symptom(4JJ3 without DPD) intermittent conditions of engine".
1) Turn OFF the ignition switch.
2) Disconnect the CMP sensor harness connector (E19).
3) Turn ON the ignition switch.
4) Measure the voltage between the CMP sensor 5 V reference circuit (pin 3 of E19) and the body ground with a DMM.
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Value: 4.5 to 5.5 V
The reading is more than the specified value.
=>Go to Inspection for short to power supply in 5 V reference circuit.
The reading is within the specified range.
Replace the CMP sensor.
Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 without DPD) CMP sensor removal".
Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 without DPD) CMP sensor installation".
The reading is less than the specified value.
=>Go to FRP sensor 5 V reference voltage check.
1) Turn OFF the ignition switch.
2) Disconnect the FRP sensor harness connector (E45).
3) Turn ON the ignition switch.
4) Measure the voltage between the CMP sensor 5 V reference circuit (pin 3 of E19) and the body ground with a DMM. Is the voltage more than or equal to the specified value?
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Value: 4.5 V
Yes
Replace the fuel rail.
Refer to "1.Engine 1C.Fuel System(4JJ3 without DPD) common rail (fuel rail) removal".
Refer to "1.Engine 1C.Fuel System(4JJ3 without DPD) common rail (fuel rail) installation".
No
=>Go to Boost pressure sensor 5 V reference voltage check.
1) Turn OFF the ignition switch.
2) Disconnect the boost pressure sensor harness connector (E31).
3) Turn ON the ignition switch.
4) Measure the voltage between the CMP sensor 5 V reference circuit (pin 3 of E19) and the body ground with a DMM. Is the voltage more than or equal to the specified value?
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Value: 4.5 V
Yes
Replace the boost pressure sensor.
Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 without DPD) boost pressure sensor removal".
Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 without DPD) boost pressure sensor installation".
No
=>Go to Accelerator pedal position sensor 2, 5 V reference voltage check.
1) Turn OFF the ignition switch.
2) Disconnect the accelerator pedal position sensor harness connector (C67).
3) Turn ON the ignition switch.
4) Measure the voltage between the CMP sensor 5 V reference circuit (pin 3 of E19) and the body ground with a DMM. Is the voltage more than or equal to the specified value?
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Value: 4.5 V
Yes
Replace the accelerator pedal.
Refer to "1.Engine 1I.Speed Control Systems(4JJ3 without DPD) accelerator pedal removal".
Refer to "1.Engine 1I.Speed Control Systems(4JJ3 without DPD) accelerator pedal installation".
No
=>Go to Inspection for short to ground in 5 V reference circuit.
1) Inspect 5 V reference circuit 2 between the ECM (pin 31 of C8) and the following components for a short to ground or a short to the low reference circuit. Is the result normal?
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
2) Inspect 5 V reference circuit 8 between the ECM (pin 30 of E3) and the following components for a short to ground or a short to the low reference circuit. Is the result normal?
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
3) Are all of the results normal?
Yes
No
Repair the circuit as necessary.
1) Inspect 5 V reference circuit 2 between the ECM (pin 31 of C8) and the following components for a short to the battery power supply circuit or a short to the ignition power supply circuit. Is the result normal?
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
2) Inspect 5 V reference circuit 8 between the ECM (pin 30 of E3) and the following components for a short to the battery power supply circuit or a short to the ignition power supply circuit. Is the result normal?
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "LHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
Refer to "RHD Engine Control (4JJ3 without DPD)" in the ETM (wiring diagram). (Open using the ETM viewer.).
3) Are all of the results normal?
Yes
No
Repair the circuit as necessary.
Note
Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 without DPD) ECM removal".
Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 without DPD) ECM installation".
Refer to "1.Engine 1Z.Engine Electrical Control(4JJ3 without DPD) ECM setting".
Procedure completion
1) Clear the DTC with a scan tool.
2) Turn OFF the ignition switch for 1 minute or more.
3) Start the engine.
4) Operate the vehicle under the conditions for running the DTC.
5) Observe the DTC information with a scan tool.