DTC TABLE [SAS CONTROL MODULE (ACTIVE BONNET)]

id0802h4080700

Caution

•  When DTCs not shown in the DTC table are displayed, perform the inspection for DTCs not shown in the DTC table. (See Inspection for DTCs not usually displayed so the related function is not equipped.)

DTC				System malfunction location	Fail-safe function	Drive cycle	Self test type*1	Memory function	Page
M-MDS display	Air bag system warning light
	Flashing pattern		Priority ranking
B0003:53	―	Flashing	4	Operation (deployment) inhibited	—	—	C, D	×	(See DTC B0003:53 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B00D3:01	―	―	―	Active bonnet warning light malfunction	—	—	C, D	×	(See DTC B00D3:01 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B00D3:29	―	―	―	Communication error with instrument cluster (active bonnet warning light status mis-matched)	—	—	C, D	×	(See DTC B00D3:29 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1001:11	19		15	Active bonnet actuator (RH) circuit short to body ground	—	—	C, D	×	(See DTC B1001:11/B1001:12/B1001:13/B1001:19/B1001:1A [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1001:12				Active bonnet actuator (RH) circuit short to power supply	—	—	C, D	×
B1001:13				Active bonnet actuator (RH) circuit open circuit or resistance high	—	—	C, D	×
B1001:19				Short circuit to active bonnet actuator (RH) circuit and active bonnet actuator (LH) circuit / other air bag module circuits	—	—	C, D	×
B1001:1A				Active bonnet actuator (RH) circuit resistance low	—	—	C, D	×
B1001:55	54		6	Configuration setting error (Active bonnet actuator (RH) structural malfunction)	—	—	C, D	×	(See DTC B1001:55, B1003:55 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1003:11	21		14	Active bonnet actuator (LH) circuit short to body ground	—	—	C, D	×	(See DTC B1003:11/B1003:12/B1003:13/B1003:19/B1003:1A [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1003:12				Active bonnet actuator (LH) circuit short to power supply	—	—	C, D	×
B1003:13				Active bonnet actuator (LH) circuit open circuit or resistance high	—	—	C, D	×
B1003:19				Short circuit to active bonnet actuator (LH) circuit and active bonnet actuator (RH) circuit / other air bag module circuits	—	—	C, D	×
B1003:1A				Active bonnet actuator (LH) circuit resistance low	—	—	C, D	×
B1003:55	54		6	Configuration setting error (active bonnet actuator (LH) structural malfunction)	—	—	C, D	×	(See DTC B1001:55, B1003:55 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1011:95	58		7	SAS control module connectors are poorly connected	—	—	C, D	×	(See DTC B1011:95 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1422:11	41		8	Active bonnet sensor (right, right or right, left or left, center) circuit short to body ground	—	—	C, D	×	(See DTC B1422:11, B1422:12, B1422:29, B1422:2B, B1422:4A, B1422:87, B1422:96 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1422:12				Active bonnet sensor (right, right or right, left or left, center) circuit short to power supply	—	—	C, D	×
B1422:29				Active bonnet sensor (right, right) internal malfunction	—	—	C, D	×
B1422:2B				Short circuit to active bonnet sensor (right, right or right, left or left, center) and other active bonnet sensor or other air bag sensor circuits	—	—	C, D	×
B1422:4A				Active bonnet sensor (right, right) ID mismatch	—	—	C, D	×
B1422:87				Signal reception error from active bonnet sensor (right, right)	—	—	C, D	×
B1422:96				Active bonnet sensor (right, right) internal malfunction	—	—	C, D	×
B1422:55	54		6	Configuration setting error (active bonnet sensor (right, right) structural malfunction)	—	—	C, D	×	(See DTC B1422:55, B1423:55, B1424:55 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1423:11	42		9	Active bonnet sensor (left, right or left, left or right, center) circuit short to body ground	—	—	C, D	×	(See DTC B1423:11, B1423:12, B1423:29, B1423:2B, B1423:4A, B1423:87, B1423:96 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1423:12				Active bonnet sensor (left, right or left, left or right, center) circuit short to power supply	—	—	C, D	×
B1423:29				Active bonnet sensor (right, center) internal malfunction	—	—	C, D	×
B1423:2B				Short circuit to active bonnet sensor (left, right or left, left or right, center) and other active bonnet sensor or other air bag sensor circuits	—	—	C, D	×
B1423:4A				Active bonnet sensor (right, center) ID mismatch	—	—	C, D	×
B1423:87				Signal reception error from active bonnet sensor (right, center)	—	—	C, D	×
B1423:96				Active bonnet sensor (right, center) internal malfunction	—	—	C, D	×
B1423:55	54		6	Configuration setting error (active bonnet sensor (right, center) structural malfunction)	—	—	C, D	×	(See DTC B1422:55, B1423:55, B1424:55 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1424:29	43		10	Active bonnet sensor (right, left) internal malfunction	—	—	C, D	×	(See DTC B1424:29, B1424:4A, B1424:87, B1424:96 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1424:4A				Active bonnet sensor (right, left) ID mismatch	—	—	C, D	×
B1424:87				Signal reception error from active bonnet sensor (right, left)	—	—	C, D	×
B1424:96				Active bonnet sensor (right, left) internal malfunction	—	—	C, D	×
B1424:55	54		6	Configuration setting error (active bonnet sensor (right, left) structural malfunction)	—	—	C, D	×	(See DTC B1422:55, B1423:55, B1424:55 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1425:29	44		11	Active bonnet sensor (left, right) internal malfunction	—	—	C, D	×	(See DTC B1425:29, B1425:4A, B1425:87, B1425:96 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1425:4A				Active bonnet sensor (left, right) ID mismatch	—	—	C, D	×
B1425:87				Signal reception error from active bonnet sensor (left, right)	—	—	C, D	×
B1425:96				Active bonnet sensor (left, right) internal malfunction	—	—	C, D	×
B1425:55	54		6	Configuration setting error (active bonnet sensor (left, right) structural malfunction)	—	—	C, D	×	(See DTC B1425:55, B1426:55, B1427:55 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1426:29	45		12	Active bonnet sensor (left, center) internal malfunction	—	—	C, D	×	(See DTC B1426:29, B1426:4A, B1426:87, B1426:96 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1426:4A				Active bonnet sensor (left, center) ID mismatch	—	—	C, D	×
B1426:87				Signal reception error from active bonnet sensor (left, center)	—	—	C, D	×
B1426:96				Active bonnet sensor (left, center) internal malfunction	—	—	C, D	×
B1426:55	54		6	Configuration setting error (active bonnet sensor (left, center) structural malfunction)	—	—	C, D	×	(See DTC B1425:55, B1426:55, B1427:55 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1427:29	46		13	Active bonnet sensor (left, left) internal malfunction	—	—	C, D	×	(See DTC B1427:29, B1427:4A, B1427:87, B1427:96 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1427:4A				Active bonnet sensor (left, left) ID mismatch	—	—	C, D	×
B1427:87				Signal reception error from active bonnet sensor (left, left)	—	—	C, D	×
B1427:96				Active bonnet sensor (left, left) internal malfunction	—	—	C, D	×
B1427:55	54		6	Configuration setting error (active bonnet sensor (left, left) structural malfunction)	—	—	C, D	×	(See DTC B1425:55, B1426:55, B1427:55 [SAS CONTROL MODULE (ACTIVE BONNET)].)
B1429:00	13		3	SAS control module operation (deployment)	—	—	C, D	×	(See DTC B1429:00 [SAS CONTROL MODULE (ACTIVE BONNET)].)
U0001:88	―	Continuously illuminated	1	Unit communication error (HS-CAN)	—	—	C, D	×	(See DTC U0001:88/U0155:00 [SAS CONTROL MODULE (ACTIVE BONNET)].)
U0100:00	14		5	PCM communication error or invalid value reception	—	—	C, D	×	(See DTC U0100:00 [SAS CONTROL MODULE (ACTIVE BONNET)].)
U0101:00				TCM communication error or invalid value reception	—	—	C, D	×	(See DTC U0101:00 [SAS CONTROL MODULE (ACTIVE BONNET)].)
U0155:00				Communication error with instrument cluster	—	—	C, D	×	(See DTC U0001:88/U0155:00 [SAS CONTROL MODULE (ACTIVE BONNET)].)
U2100:00	―	Flashing	4	Configuration not set	—	—	C, D	×	(See DTC U2100:00 [SAS CONTROL MODULE (ACTIVE BONNET)].)
U2107:00	―	―	―	SAS control module collision judgement signal output (secondary collision reduction signal output)	―	―	C, D	×	(See DTC U2107:00 [SAS CONTROL MODULE (ACTIVE BONNET)].)
U3000:49	12		2	SAS control module internal malfunction	—	—	C, D	×	(See DTC U3000:49 [SAS CONTROL MODULE (ACTIVE BONNET)].)
	―	Continuously illuminated	1
U3003:16	―	Continuously illuminated	1	SAS control module power supply voltage decreases (8 V or less)	—	—	C, D	×	(See DTC U3003:16/U3003:17 [SAS CONTROL MODULE (ACTIVE BONNET)].)
U3003:17				SAS control module power supply voltage increases (16 V or more)	—	—	C, D	×

Inspection for DTCs not usually displayed so the related function is not equipped

Diagnostic procedure

Step	Inspection		Action
1	INSPECT FOR ANY DTC DISPLAYED SIMULTANEOUSLY •  Is any DTC not shown in the DTC table displayed simultaneously?	Yes	Repair the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [SAS CONTROL MODULE (ACTIVE BONNET)].)
		No	Go to the next step.
2	VERIFY IF MALFUNCTION CAUSED BY TEMPORARY MALFUNCTION IN SAS CONTROL MODULE •  Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE (ACTIVE BONNET)].) •  Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (ACTIVE BONNET)].) •  Are the same DTCs displayed?	Yes	Go to the next step.
		No	DTC troubleshooting completed.
3	VERIFY IF MALFUNCTION CAUSED BY CONFIGURATION ERROR •  Perform the SAS control module configuration using the M-MDS. (See SAS CONTROL MODULE CONFIGURATION (USING AS-BUILT DATA) [TWO-STEP DEPLOYMENT CONTROL SYSTEM].) •  Clear the DTC for the SAS control module using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE (ACTIVE BONNET)].) •  Perform the DTC inspection for the SAS control module using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (ACTIVE BONNET)].) •  Are the same DTCs displayed?	Yes	Re-perform the configuration, then perform the DTC inspection. •  If the same DTC is displayed, replace the SAS control module. (See SAS CONTROL MODULE REMOVAL/INSTALLATION [TWO-STEP DEPLOYMENT CONTROL SYSTEM].)
		No	DTC troubleshooting completed.