DTC P0732 [FN4A-EL]


DTC P0732	Gear 2 incorrect (incorrect gear ratio detected)
DETECTION CONDITION	• The PCM comperes the revolution ratio of the forward clutch drum to the differential gear case revolution when the following monitoring conditions are met. If revolution ratio is 1.277 or less or 2.185 or more, the PCM determines that there is a malfunction. Monitoring conditions: - ATF temperature 20 °C {68 °F} or more - Driving in 2 GR in D or M range - Engine running - Turbine speed within 225-4,987 rpm - Differential gear case (output) revolution speed 35 rpm or more - None of the following DTCs are present: P0706, P0707, P0708, P0712, P0713, P0715, P0720, P0751, P0752, P0753, P0756, P0757, P0758, P0761, P0762, P0763, P0766, P0767, P0768, P0771, P0772, P0773 Diagnostic support note: • This is a continuous monitor (CCM). • The MIL does not illuminate. • The AT warning light illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA is not available. • A PENDING CODE is not available. • The DTC is stored in the PCM memory.
POSSIBLE CAUSE	• ATF level low • Deteriorated ATF • Shift solenoids A, B or C stuck • Pressure control solenoid stuck • Line pressure low 2-4 brake band slipping • Forward clutch slipping • Control valve stuck • Oil pump malfunction • PCM malfunction


STEP	INSPECTION		ACTION
1	VERIFY RELATED REPAIR INFORMATION AVAILABILITY • Verify related Service Bulletins and/or on-line repair information availability. • Is any related repair information available?	Yes	Perform repair or diagnosis according to the available repair information.
1		No	Go to the next step.
2	INSPECT ATF CONDITION • Inspect the ATF condition. (See AUTOMATIC TRANSAXLE FLUID (ATF) INSPECTION [FN4A-EL].) • Is it normal?	Yes	Go to the next step.
2		No	Replace the transaxle, then go to Step 8.
3	INSPECT ATF LEVEL • Start the engine. • Warm up the ATX. • Is the ATF level within the specification? (See AUTOMATIC TRANSAXLE FLUID (ATF) INSPECTION [FN4A-EL].)	Yes	Go to the next step.
3		No	Add ATF to the specified level, then go to Step 8.
4	INSPECTION SHIFT SOLENOID VALVE A, B AND C FOR CLICK SOUND • Perform operation inspection. (See SOLENOID VALVE INSPECTION [FN4A-EL].) • Verify the click sound of shift solenoid A, B, and C when applying B+ to each transaxle terminal. • Was a click heard from solenoids?	Yes	Go to the next step.
4		No	Replace the solenoid where you could not hear a click sound, then go to Step 8. (See SOLENOID VALVE REMOVAL/INSTALLATION [FN4A-EL].)
5	INSPECT LINE PRESSURE • Start the engine. • Measure the line pressures. Specification Idle: 330-470 kPa {3.4-4.7 kgf/cm², 48-68 psi} Stall: 990-1,160 kPa {10.1-11.8 kgf/cm², 144-168 psi} • Are the line pressures within the specifications? (See Line Pressure Test.)	Yes	Go to the next step.
5		No	All ranges: Replace the oil pump, then go to Step 8. Any ranges: Replace the control valve body, then go to Step 8. (See CONTROL VALVE BODY REMOVAL [FN4A-EL].) (See CONTROL VALVE BODY INSTALLATION [FN4A-EL].)
6	INSPECT STALL SPEED • Measure the stall speed in D range. (See Stall Test.) Specification 2,200-2,800 rpm • Is the stall speed within the specification?	Yes	Go to the next step.
6		No	Replace the automatic transaxle, then go to Step 8. (See AUTOMATIC TRANSAXLE REMOVAL/INSTALLATION [FN4A-EL].)
7	INSPECT FREQUENCY OF INPUT/TURBINE SPEED SENSOR WHEN DRIVING VEHICLE • Turn the ignition switch to the LOCK position. • Connect the WDS or equivalent. • Start the engine. • Measure the frequency of input/turbine speed sensor while driving vehicle under the following conditions: - Vehicle speed (VSS PID): 40 km/h {24 mph} - Drive in the D range, 2GR - Throttle opening angle (TP PID): approx. 25% • Was the frequency of the input/turbine speed sensor at approx. 1,250 Hz?	Yes	Go to the next step.
7		No	Replace the control valve body, then go to the next step. (See CONTROL VALVE BODY REMOVAL [FN4A-EL].) (See CONTROL VALVE BODY INSTALLATION [FN4A-EL].)
8	VERIFY REPAIR OF DTC P0732 • Make sure to reconnect all the disconnected connectors. • Clear the DTC using the WDS or equivalent. • Start the engine. • Warm up the transaxle. • Drive the vehicle under the following conditions at least 3 times for more than 1 s: - ATF temperature: 20 °C {68 °F} or more - Drive in the D range, 2GR - Vehicle speed (VSS PID): 3.8 km/h {2.4 mph} or more • Are any DTCs present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [ZY].)
8		No	Go to the next step.
9	VERIFY AFTER REPAIR PROCEDURE • Perform the "After Repair Procedure". (See AFTER REPAIR PROCEDURE [FN4A-EL].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection.
9		No	DTC troubleshooting completed.