DTC P2109:00 [ZJ, ZY]

id0102c0708000

DTC P2109:00

TP sensor minimum stop range/performance problem

DETECTION CONDITION

•  If the fully-open throttle position is 5.1 ° or lower, or 15.9 ° or more even though the fully-open throttle position learning is finished.

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The MIL illuminates if the PCM detects the above malfunction condition in the first drive cycle.

•  FREEZE FRAME DATA is available.

•  The DTC is stored in the PCM memory.

POSSIBLE CAUSE

•  Improper operation of drive-by-wire control system

•  Throttle valve actuator malfunction

•  Throttle valve malfunction

•  PCM malfunction

DTC P2109:00	TP sensor minimum stop range/performance problem
DETECTION CONDITION	• If the fully-open throttle position is 5.1 ° or lower, or 15.9 ° or more even though the fully-open throttle position learning is finished. Diagnostic support note • This is a continuous monitor (CCM). • The MIL illuminates if the PCM detects the above malfunction condition in the first drive cycle. • FREEZE FRAME DATA is available. • The DTC is stored in the PCM memory.
POSSIBLE CAUSE	• Improper operation of drive-by-wire control system • Throttle valve actuator malfunction • Throttle valve malfunction • PCM malfunction

Diagnostic procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT DRIVE-BY-WIRE CONTROL SYSTEM OPERATION • Perform the Drive-by-wire Control System Inspection. (See ENGINE CONTROL SYSTEM OPERATION INSPECTION [ZJ, ZY].) • Is there any malfunction?	Yes	Repair or replace the malfunctioning part according to the inspection results, then go to Step 6.
3		No	Go to the next step.
4	INSPECT THROTTLE VALVE ACTUATOR • Inspect the throttle valve actuator. (See THROTTLE BODY INSPECTION [ZJ, ZY].) • Is there any malfunction?	Yes	Replace the throttle body, then go to Step 6. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [ZJ, ZY].)
4		No	Go to the next step.
5	INSPECT THROTTLE VALVE • Inspect the throttle valve. (See THROTTLE BODY INSPECTION [ZJ, ZY].) • Is there any malfunction?	Yes	Replace the throttle body, then go to the next step. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [ZJ, ZY].)
5		No	Go to the next step.
6	VERIFY DTC TROUBLESHOOTING COMPLETED • Make sure to reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [ZJ, ZY].) • Perform the KOER self test. (See KOEO/KOER SELF TEST [ZJ, ZY].) • Is the same DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [ZJ, ZY].)
6		No	Go to the next step.
7	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [ZJ, ZY].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [ZJ, ZY].)
7		No	DTC troubleshooting completed.