DTC P0016:00 [MZ-CD 1.6]
id0102g8145600
|
DTC P0016:00 |
Crankshaft position (CKP) sensor circuit range /performance |
|---|---|
|
DETECTION CONDITION
|
• The PCM monitors the camshaft and crankshaft output signals. If the camshaft output signal is not synchronized with the crankshaft output signal, the PCM determines that there is a malfunction in the CKP sensor circuit.
|
|
POSSIBLE CAUSE
|
• CMP sensor connector or terminal malfunction
• CKP sensor connector or terminal malfunction
• CMP sensor malfunction
• CKP sensor malfunction
• PCM connector or terminal malfunction
• Camshaft pulley malfunction
• Crankshaft pulse wheel malfunction
• PCM malfunction
|
Diagnostic procedure
|
STEP |
INSPECTION |
ACTION |
|
|---|---|---|---|
|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has the FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
|
||
|
2
|
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
• Verify related service repair information availability.
• Is any related repair information available?
|
Yes
|
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to the next step.
|
|
No
|
Go to the next step.
|
||
|
3
|
INSPECT CMP SENSOR CONNECTOR CONDITION
• Switch the ignition to off.
• Disconnect the CMP sensor connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion)
• Is there any malfunction?
|
Yes
|
Repair or replace the connector and/or terminals, then go to Step 10.
|
|
No
|
Go to the next step.
|
||
|
4
|
INSPECT CKP SENSOR CONNECTOR CONDITION
• Switch the ignition to off.
• Disconnect the CKP sensor connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion)
• Is there any malfunction?
|
Yes
|
Repair or replace the connector and/or terminals, then go to Step 10.
|
|
No
|
Go to the next step.
|
||
|
5
|
INSPECT CMP SENSOR
• Inspect the CMP sensor.
• Is there any malfunction?
|
Yes
|
Replace the CMP sensor, then go to Step 10.
|
|
No
|
Go to the next step.
|
||
|
6
|
INSPECT CKP SENSOR
• Inspect the CKP sensor.
• Is there any malfunction?
|
Yes
|
Replace the CKP sensor, then go to Step 10.
|
|
No
|
Go to the next step.
|
||
|
7
|
INSPECT PCM CONNECTOR CONDITION
• Disconnect the PCM connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion)
• Is there any malfunction?
|
Yes
|
Repair or replace the connector and/or terminals, then go to Step 10.
|
|
No
|
Go to the next step.
|
||
|
8
|
INSPECT CMP SENSOR PULSE WHEEL
• Visually inspect the CMP sensor pulse wheel (camshaft pulley).
• Is there any malfunction?
|
Yes
|
Replace the camshaft pulley, then go to Step 10.
|
|
No
|
Go to the next step.
|
||
|
9
|
INSPECT CKP SENSOR PULSE WHEEL
• Visually inspect the CKP sensor pulse wheel.
• Is there any malfunction?
|
Yes
|
Replace the crankshaft pulse wheel, then go to the next step.
|
|
No
|
Go to the next step.
|
||
|
10
|
VERIFY THAT DTC P0016:00 TROUBLESHOOTING IS COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Run the vehicle under the FREEZE FRAME DATA stored condition.
• Is the same DTC present?
|
Yes
|
Repeat the inspection from Step 1.
• If the malfunction recurs, replace the PCM.
Go to the next step.
|
|
No
|
Go to the next step.
|
||
|
11
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the after repair procedure.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZ-CD 1.6].)
|
|
No
|
DTC troubleshooting completed.
|
||