DTC P02ED:00, P02ED:68 [MZ-CD 1.6]
id0102g8571600
|
DTC P02ED:00 DTC P02ED:68 |
Intake shutter valve control system - low airflow detected |
|---|---|
|
DETECTION CONDITION
|
• The PCM monitors the intake shutter valve signal at engine speeds between 700 rpm and 4,000 rpm and engine torque between 5 N·m and 300 N·m. If the intake shutter valve is under the following condition, the PCM determines that low airflow is detected in the intake shutter valve control system.
|
|
POSSIBLE CAUSE
|
• Connector or terminal malfunction
• Obstruction in intake shutter valve
• Intake shutter valve malfunction
• PCM malfunction
|
Diagnostic procedure
|
STEP |
INSPECTION |
ACTION |
|
|---|---|---|---|
|
1
|
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
• Has the FREEZE FRAME DATA been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
|
||
|
2
|
VERIFY RELATED REPAIR INFORMATION AVAILABILITY
• Verify related service repair information availability.
• Is any related repair information available?
|
Yes
|
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to the next step.
|
|
No
|
Go to the next step.
|
||
|
3
|
VERIFY RELATED PENDING CODE AND/OR DTC
• Switch the ignition to ON (engine off).
• Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.
• Is the other PENDING CODE/DTC also present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZ-CD 1.6].)
|
|
No
|
Go to the next step.
|
||
|
4
|
INSPECT INTAKE SHUTTER VALVE CONNECTOR FOR POOR CONNECTION
• Switch the ignition to off.
• Disconnect the intake shutter valve connector.
• Inspect for poor connection (such as damaged/pulled-out pins, and corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace terminal, then go to Step 7.
|
|
No
|
Go to the next step.
|
||
|
5
|
VISUALLY INSPECT INTAKE SHUTTER VALVE
• Disconnect the intake shutter valve connector.
• Visually inspect the intake shutter valve.
• Is there any obstruction (carbon deposit etc.) in intake shutter valve?
|
Yes
|
Remove the obstruction, then go to the next step.
|
|
No
|
Go to the next step.
|
||
|
6
|
INSPECT THE INTAKE SHUTTER VALVE
• Inspect the intake shutter valve.
• Is the intake shutter valve normal?
|
Yes
|
Go to the next step.
|
|
No
|
Replace the intake shutter valve.
Then go to the next step.
|
||
|
7
|
VERIFY THAT DTC P02ED:00, P02ED:68 TROUBLESHOOTING IS COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Run the vehicle under the FREEZE FRAME DATA stored condition.
• Is the same DTC present?
|
Yes
|
Repeat the inspection from Step 1.
• If the malfunction recurs, replace the PCM.
Go to the next step.
|
|
No
|
Go to the next step.
|
||
|
8
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the after repair procedure.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZ-CD 1.6].)
|
|
No
|
DTC troubleshooting completed.
|
||