360°VIEW MONITOR IMAGES ARE NOT TRANSPARENT [360°VIEW MONITOR SYSTEM]

id1503b8032300

Note

• Due to environmental effects, the system behavior may differ from the driver’s intentions even though the vehicle has no malfunction. To perform symptom troubleshooting, an understanding of the applicable system from the new vehicle instruction is required. For details on the control conditions of the system, refer to the [360° VIEW MONITOR SYSTEM] operation in the service highlights/technical guide.

Outline

Description

•  360° view monitor images are not transparent.

Possible cause

•  Front camera lens is damaged

•  Side camera lens is damaged

•  Rear mount camera lens is damaged

•  360° view monitor control module malfunction.

Diagnostic Procedure

Step

Inspection

Results

Action

1

VERIFY ALL SYSTEM DTCs

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

Go to the next step.

2

VERIFY FRONT CAMERA, SIDE CAMERAS, AND REAR MOUNT CAMERA CONDITIONS

•  Visually verify the lens of the applicable part.

•  Is the part normal?

Yes

Wipe the lens surface of the camera using a soft cloth with detergent. Wipe the lens surface of the camera with a dry soft cloth, then go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

(See FRONT CAMERA REMOVAL/INSTALLATION.)

(See SIDE CAMERA REMOVAL/INSTALLATION.)

(See REAR MOUNT CAMERA REMOVAL/INSTALLATION.)

Repair completion verification

VERIFY THAT VEHICLE IS REPAIRED

•  Install/connect the part removed/disconnected during the troubleshooting procedure.

•  Has the malfunction symptom been eliminated?

Yes

Complete the symptom troubleshooting. (Explain contents of repair to customer)

No

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction is not resolved, replace the 360° view monitor control module.
(See 360°VIEW MONITOR CONTROL MODULE REMOVAL/INSTALLATION [(E)].)

Description	• 360° view monitor images are not transparent.
Possible cause	• Front camera lens is damaged • Side camera lens is damaged • Rear mount camera lens is damaged • 360° view monitor control module malfunction.

Step	Inspection	Results	Action
1	VERIFY ALL SYSTEM DTCs • Perform the DTC inspection. (See DTC INSPECTION.) • Are any DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
1		No	Go to the next step.
2	VERIFY FRONT CAMERA, SIDE CAMERAS, AND REAR MOUNT CAMERA CONDITIONS • Visually verify the lens of the applicable part. • Is the part normal?	Yes	Wipe the lens surface of the camera using a soft cloth with detergent. Wipe the lens surface of the camera with a dry soft cloth, then go to the next step.
2		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See FRONT CAMERA REMOVAL/INSTALLATION.) (See SIDE CAMERA REMOVAL/INSTALLATION.) (See REAR MOUNT CAMERA REMOVAL/INSTALLATION.)
Repair completion verification	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Has the malfunction symptom been eliminated?	Yes	Complete the symptom troubleshooting. (Explain contents of repair to customer)
Repair completion verification		No	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [(E)].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction is not resolved, replace the 360° view monitor control module. (See 360°VIEW MONITOR CONTROL MODULE REMOVAL/INSTALLATION [(E)].)