DTC C0061:54/C0063:54 [DYNAMIC STABILITY CONTROL (DSC)]

id0402b2888100

Note
•  Vehicles with combined sensor: Applied VIN (assumed)
European (L.H.D. U.K.) specs.
•  JMZ BL12F60# 100001—181415
•  JMZ BL12F70# 100001—181415
•  JMZ BL12Y20# 100001—181415
•  JMZ BL12Z20# 100001—181415
•  JMZ BL12Z50# 100001—181415
•  JMZ BL14F60# 100001—181415
•  JMZ BL14F70# 100001—181415
•  JMZ BL14Y20# 100001—181415
•  JMZ BL14Z20# 100001—181415
•  JMZ BL14Z50# 100001—181415
•  JMZ BLA2A60# 100001—181415
•  JMZ BLA2C60# 100001—181415
•  JMZ BLA2F70# 100001—181415
•  JMZ BLA2G60# 100001—181415
•  JMZ BLA2Y60# 100001—181415
•  JMZ BLA2Z20# 100001—181415
•  JMZ BLA2Z50# 100001—181415
•  JMZ BLA4360# 100001—181415
•  JMZ BLA4A60# 100001—181415
•  JMZ BLA4C60# 100001—181415
•  JMZ BLA4F70# 100001—181415
•  JMZ BLA4G60# 100001—181415
•  JMZ BLA4Y60# 100001—181415
•  JMZ BLA4Z20# 100001—181415
•  JMZ BLA4Z50# 100001—181415
Australian specs.
•  JM0 BL103100 100001—225632
•  JM0 BL10C100 100001—225632
•  JM0 BL10F100 100001—225632
•  JM0 BL10L100 100001—225632
General (R.H.D.) specs.
•  JM6 BL1031*0 100001—225632
•  JM6 BL1051*0 100001—225632
•  JM6 BL10F1*0 100001—225632
•  JM6 BL10L1*0 100001—225632
•  JM6 BL10Z1*0 100001—225632
General (L.H.D.) specs., Arab Gulf Cooperation Council, China
•  JM7 BL04F**# 100001—225632
•  JM7 BL04Z**# 100001—225632
•  JM7 BL12F**# 100001—225632
•  JM7 BL12Z**# 100001—225632
•  JM7 BL14F**# 100001—225632
•  JM7 BL14Z**# 100001—225632
•  JM7 BL22F**# 100001—225632
•  JM7 BL22Z**# 100001—225632
•  JM7 BL24F**# 100001—225632
•  JM7 BL24Z**# 100001—225632
•  Vehicles without combined sensor: Applied VIN (assumed)
European (L.H.D. U.K.) specs.
•  JMZ BL12F60# 181416—
•  JMZ BL12F70# 181416—
•  JMZ BL12Y20# 181416—
•  JMZ BL12Z20# 181416—
•  JMZ BL12Z50# 181416—
•  JMZ BL14F60# 181416—
•  JMZ BL14F70# 181416—
•  JMZ BL14Y20# 181416—
•  JMZ BL14Z20# 181416—
•  JMZ BL14Z50# 181416—
•  JMZ BLA2A60# 181416—
•  JMZ BLA2C60# 181416—
•  JMZ BLA2F70# 181416—
•  JMZ BLA2G60# 181416—
•  JMZ BLA2Y60# 181416—
•  JMZ BLA2Z20# 181416—
•  JMZ BLA2Z50# 181416—
•  JMZ BLA4360# 181416—
•  JMZ BLA4A60# 181416—
•  JMZ BLA4C60# 181416—
•  JMZ BLA4F70# 181416—
•  JMZ BLA4G60# 181416—
•  JMZ BLA4Y60# 181416—
•  JMZ BLA4Z20# 181416—
•  JMZ BLA4Z50# 181416—
Australian specs.
•  JM0 BL103100 225633—
•  JM0 BL10C100 225633—
•  JM0 BL10F100 225633—
•  JM0 BL10L100 225633—
General (R.H.D.) specs.
•  JM6 BL1031*0 225633—
•  JM6 BL1051*0 225633—
•  JM6 BL10F1*0 225633—
•  JM6 BL10L1*0 225633—
•  JM6 BL10Z1*0 225633—
General (L.H.D.) specs., Arab Gulf Cooperation Council, China
•  JM7 BL04F**# 225633—
•  JM7 BL04Z**# 225633—
•  JM7 BL12F**# 225633—
•  JM7 BL12Z**# 225633—
•  JM7 BL14F**# 225633—
•  JM7 BL14Z**# 225633—
•  JM7 BL22F**# 225633—
•  JM7 BL22Z**# 225633—
•  JM7 BL24F**# 225633—
•  JM7 BL24Z**# 225633—

DTC
C0061:54, C0063:54
DSC HU/CM system (unperformed initialization procedure)
DETECTION CONDITION
•  Vehicles with combined sensor
―  C0061:54
•  DSC detects that the initialization procedure for combined sensor has not been performed. (lateral-G sensor)
―  C0063:54
•  DSC detects that the initialization procedure for combined sensor has not been performed. (yaw rate sensor)
•  Vehicles without combined sensor
―  C0061:54
•  DSC HU/CM detects that the initialization procedure has not been performed. (low-G sensor)
―  C0063:54
•  DSC HU/CM detects that the initialization procedure has not been performed. (yaw rate sensor)
POSSIBLE CAUSE
•  Vehicles with combined sensor
―  Initialization procedure for the combined sensor not performed
―  Combined sensor malfunction
―  DSC HU/CM malfunction
•  Vehicles without combined sensor
―  Initialization procedure for the low-G sensor or yaw rate sensor not performed
―  SAS control module malfunction
―  DSC HU/CM malfunction

Diagnostic procedure (vehicles with combined sensor)

STEP

INSPECTION

ACTION
1
VERIFY INITIALIZATION PROCEDURE
•  Was the combined sensor initialization procedure performed?
Yes
Go to the next step.
No
Perform the combined sensor initialization procedure, then go to Step 3.
(See DSC SENSOR INITIALIZATION PROCEDURE.)
2
INSPECT COMBINED SENSOR
•  Inspect the combined sensor.
•  Is the combined sensor normal?
Yes
Go to the next step.
No
Replace the combined sensor, then go to the next step.
(See COMBINED SENSOR REMOVAL/INSTALLATION.)
3
VERIFY THAT THE SAME DTC IS NOT PRESENT
•  Clear the DTCs from the memory.
•  Are the same DTCs present?
Yes
Repeat the inspection from Step 1.
If the malfunction recurs, replace the DSC HU/CM, then go to the next step.
(See DSC HU/CM REMOVAL/INSTALLATION.)
No
Go to the next step.
4
VERIFY THAT NO OTHER DTCS ARE PRESENT
•  Are any other DTCs output?
Yes
Go to the applicable DTC inspection.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)
No
DTC troubleshooting completed.

Diagnostic procedure (vehicles without combined sensor)

STEP

INSPECTION

ACTION
1
VERIFY INITIALIZATION PROCEDURE
•  Was the DSC sensor initialization procedure performed?
Yes
Go to the next step.
No
Perform the DSC sensor initialization procedure, then go to Step 3.
(See DSC SENSOR INITIALIZATION PROCEDURE.)
2
INSPECT SAS CONTROL MODULE MALFUNCTION
•  Switch the ignition to off.
•  Using the M-MDS, perform the DTC inspection for the SAS control module.
•  Are any DTCs detected?
Yes
Go to applicable DTC inspection.
(See DTC TABLE [TYPE B].)
No
Go to the next step.
3
VERIFY THAT THE SAME DTC IS NOT PRESENT
•  Clear the DTCs from the memory.
•  Are the same DTCs present?
Yes
Repeat the inspection from Step 1.
If the malfunction recurs, replace the DSC HU/CM, then go to the next step.
(See DSC HU/CM REMOVAL/INSTALLATION.)
No
Go to the next step.
4
VERIFY THAT NO OTHER DTCS ARE PRESENT
•  Are any other DTCs output?
Yes
Go to the applicable DTC inspection.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)
No
DTC troubleshooting completed.