GENERAL PROCEDURES (BRAKE)


id041000800100


Wheel and Tire Installation

1.  When installing the wheels and tires, tighten the wheel nuts in a criss-cross pattern to the following tightening torque.

Tightening torque
88—118 N·m {9.0—12 Kgf·m, 65—87 ft·lbf}

Brake Lines Disconnection

1.  If any brake line has been disconnected during the procedures, add brake fluid, bleed the brakes, and inspect for leakage after the procedure has been completed.

Caution
•  Brake fluid will damage painted surfaces. Be careful not to spill any on painted surfaces. If it is spilled, wipe it off immediately.

Brake Pipe Flare Nut Tightening

1.  Tighten the brake pipe flare nut using the commercially available flare nut wrench.


Connector Disconnection

1.  Disconnect the negative battery cable before performing any work that requires handling of connectors. (See BATTERY REMOVAL/INSTALLATION [ZY, Z6].) (See BATTERY REMOVAL/INSTALLATION [LF, L5].) (See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI i-stop].) (See BATTERY REMOVAL/INSTALLATION [L3 Turbo].) (See BATTERY REMOVAL/INSTALLATION [MZ-CD 1.6 (Y6)].) (See BATTERY REMOVAL/INSTALLATION [MZR-CD 2.2].)


ABS/DSC Related Parts

1.  Make sure that there are no DTCs in the ABS/DSC memory after working on ABS/DSC related parts. If there are any DTCs in the memory, clear them.


DSC Related Parts Sensor Initialization Procedure

Warning
•  If the initialization procedure is not completed, the DSC will not operate properly and it might cause an unexpected accident. Therefore, when replacing or removing the following parts, make sure to perform the initialization procedure to ensure proper DSC operation.
Note
•  Vehicles with combined sensor: Applied VIN (assumed)
European (L.H.D. U.K.) specs.
•  JMZ BL12F60# 100001—181415
•  JMZ BL12F70# 100001—181415
•  JMZ BL12Y20# 100001—181415
•  JMZ BL12Z20# 100001—181415
•  JMZ BL12Z50# 100001—181415
•  JMZ BL14F60# 100001—181415
•  JMZ BL14F70# 100001—181415
•  JMZ BL14Y20# 100001—181415
•  JMZ BL14Z20# 100001—181415
•  JMZ BL14Z50# 100001—181415
•  JMZ BLA2A60# 100001—181415
•  JMZ BLA2C60# 100001—181415
•  JMZ BLA2F70# 100001—181415
•  JMZ BLA2G60# 100001—181415
•  JMZ BLA2Y60# 100001—181415
•  JMZ BLA2Z20# 100001—181415
•  JMZ BLA2Z50# 100001—181415
•  JMZ BLA4360# 100001—181415
•  JMZ BLA4A60# 100001—181415
•  JMZ BLA4C60# 100001—181415
•  JMZ BLA4F70# 100001—181415
•  JMZ BLA4G60# 100001—181415
•  JMZ BLA4Y60# 100001—181415
•  JMZ BLA4Z20# 100001—181415
•  JMZ BLA4Z50# 100001—181415
Australian specs.
•  JM0 BL103100 100001—225632
•  JM0 BL10C100 100001—225632
•  JM0 BL10F100 100001—225632
•  JM0 BL10L100 100001—225632
General (R.H.D.) specs.
•  JM6 BL1031*0 100001—225632
•  JM6 BL1051*0 100001—225632
•  JM6 BL10F1*0 100001—225632
•  JM6 BL10L1*0 100001—225632
•  JM6 BL10Z1*0 100001—225632
General (L.H.D.) specs., Arab Gulf Cooperation Council, China
•  JM7 BL04F**# 100001—225632
•  JM7 BL04Z**# 100001—225632
•  JM7 BL12F**# 100001—225632
•  JM7 BL12Z**# 100001—225632
•  JM7 BL14F**# 100001—225632
•  JM7 BL14Z**# 100001—225632
•  JM7 BL22F**# 100001—225632
•  JM7 BL22Z**# 100001—225632
•  JM7 BL24F**# 100001—225632
•  JM7 BL24Z**# 100001—225632
•  Vehicles without combined sensor: Applied VIN (assumed)
European (L.H.D. U.K.) specs.
•  JMZ BL12F60# 181416—
•  JMZ BL12F70# 181416—
•  JMZ BL12Y20# 181416—
•  JMZ BL12Z20# 181416—
•  JMZ BL12Z50# 181416—
•  JMZ BL14F60# 181416—
•  JMZ BL14F70# 181416—
•  JMZ BL14Y20# 181416—
•  JMZ BL14Z20# 181416—
•  JMZ BL14Z50# 181416—
•  JMZ BLA2A60# 181416—
•  JMZ BLA2C60# 181416—
•  JMZ BLA2F70# 181416—
•  JMZ BLA2G60# 181416—
•  JMZ BLA2Y60# 181416—
•  JMZ BLA2Z20# 181416—
•  JMZ BLA2Z50# 181416—
•  JMZ BLA4360# 181416—
•  JMZ BLA4A60# 181416—
•  JMZ BLA4C60# 181416—
•  JMZ BLA4F70# 181416—
•  JMZ BLA4G60# 181416—
•  JMZ BLA4Y60# 181416—
•  JMZ BLA4Z20# 181416—
•  JMZ BLA4Z50# 181416—
Australian specs.
•  JM0 BL103100 225633—
•  JM0 BL10C100 225633—
•  JM0 BL10F100 225633—
•  JM0 BL10L100 225633—
General (R.H.D.) specs.
•  JM6 BL1031*0 225633—
•  JM6 BL1051*0 225633—
•  JM6 BL10F1*0 225633—
•  JM6 BL10L1*0 225633—
•  JM6 BL10Z1*0 225633—
General (L.H.D.) specs., Arab Gulf Cooperation Council, China
•  JM7 BL04F**# 225633—
•  JM7 BL04Z**# 225633—
•  JM7 BL12F**# 225633—
•  JM7 BL12Z**# 225633—
•  JM7 BL14F**# 225633—
•  JM7 BL14Z**# 225633—
•  JM7 BL22F**# 225633—
•  JM7 BL22Z**# 225633—
•  JM7 BL24F**# 225633—
•  JM7 BL24Z**# 225633—

1.  When replacing or removing the following parts, perform the initialization procedure. (See DSC SENSOR INITIALIZATION PROCEDURE.)

•  DSC HU/CM
•  Combined sensor (vehicles with combined sensor)