DTC P2097 [LF ATX (FN4A-EL), L3 ATX]

id0102b6810900

DTC P2097

Target A/F feedback system too rich
DETECTION CONDITION
•  The PCM monitors the target A/F fuel trim when under the target A/F feedback control. If the fuel trim is less than specification, the PCM determines that the target A/F feedback system is too rich.
Diagnostic support note
•  This is a continuous monitor. (Fuel system)
•  The MIL illuminates if the PCM detects the above malfunctioning condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.
•  PENDING CODE is available if the PCM detects the above malfunction conditions during the first drive cycle.
•  FREEZE FRAME DATA is available.
•  Are any DTCs is stored in the PCM memory.
POSSIBLE CAUSE
•  Leakage exhaust gas
•  HO2S malfunction
•  IAT sensor malfunction
•  ECT sensor malfunction
•  A/F sensor malfunction
•  Excessive fuel line pressure
•  Fuel pump unit malfunction
•  Purge valve malfunction
•  Insufficient engine compression
•  PCM malfunction

Diagnostic procedure

STEP

INSPECTION

ACTION
1
VERIFY FREEZE FRAME DATA HAVE BEEN RECORDED
•  Have FREEZE FRAME DATA been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY RELATED PENDING CODE OR STORED DTC
•  Turn the ignition switch off, then to the ON position (Engine off).
•  Verify the related PENDING CODE or stored DTCs.
•  Is the DTC P2178 or P2188 also present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [LF ATX (FN4A-EL), L3 ATX].)
No
Go to the next step.
4
IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA
•  Is the DTC P2097 on FREEZE FRAME DATA?
Yes
Go to the next step.
No
Go to FREEZE FRAME DATA DTC inspection.
(See DTC TABLE [LF ATX (FN4A-EL), L3 ATX].)
5
VERIFY CURRENT INPUT SIGNAL STATUS OF HO2S
•  Connect the M-MDS to the DLC-2.
•  Start the engine and warm it up completely.
•  Access O2S12 PID.
•  Read O2S12 PID under following accelerator pedal condition (in NEUTRAL).
―  More than 0.45 V when accelerator pedal is suddenly depressed (rich condition).
―  Less than 0.45 V just after release of accelerator pedal (lean condition)
•  Is the PID normal?
Yes
Go to the next step.
No
Visually inspect for the exhaust gas leakage between TWC and HO2S.
•  If there is no leakage, replace the HO2S.
Then go to Step 11.
6
VERIFY CURRENT INPUT SIGNAL STATUS
•  Connect the M-MDS to the DLC-2.
•  Verify the following PIDs:
―  ECT
―  MAF
―  TP1
―  VSS
•  Are the PIDs normal?
Yes
Go to the next step.
No
Inspect the malfunctioning part according to the inspection results.
Then go to Step 11.
7
VERIFY CURRENT INPUT SIGNAL STATUS UNDER FREEZE FRAME DATA CONDITION
•  Connect the M-MDS to the DLC-2.
•  Verify the following PIDs under FREEZE FRAME DATA condition.
―  ECT
―  MAF
―  TP1
―  VSS
•  Are the PIDs normal?
Yes
Go to the next step.
No
Inspect the malfunctioning part according to the inspection results.
Then go to Step 11.
8
VERIFY CURRENT INPUT SIGNAL STATUS OF A/F SENSOR
•  Connect the M-MDS to the DLC-2.
•  Start the engine and warm it up completely.
•  Access O2S11 PID.
•  Read O2S11 PID under following accelerator pedal condition (in NEUTRAL).
―  -1.0 —1.0 A when idle.
―  More than 0.25 mA just after release of accelerator pedal (lean condition).
•  Is the PID normal?
Yes
Go to the next step.
No
Visually inspect for exhaust gas leakage between the exhaust manifold and A/F sensor.
•  If there is no leakage, replace the A/F sensor.
Then go to Step 11.
9
INSPECT FUEL LINE PRESSURE
•  Perform the “FUEL LINE PRESSURE INSPECTION”.
•  Is there any malfunction?
Yes
Replace the fuel pump unit, then go to Step 11.
(See FUEL PUMP UNIT REMOVAL/INSTALLATION [LF, L3].)
No
Go to the next step.
10
INSPECT LONG TERM FUEL TRIM
•  Connect the M-MDS to the DLC-2.
•  Access LONGFT1 PID.
•  Compare the LONGFT1 PID with recorded FREEZE FRAME DATA at Step 1.
•  Is the LONGFT1 PID above FREEZE FRAME DATA?
Yes
Inspect the purge valve.
(See PURGE SOLENOID VALVE INSPECTION [LF, L3].)
•  If there is any malfunction, replace the purge valve.
Then go to Step 11.
No
Go to the next step.
11
VERIFY TROUBLESHOOTING OF DTC P2097 COMPLETED
•  Make sure to reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Perform the PCM Adaptive Memory Produce Drive Mode.
•  Is the PENDING CODE for this DTC present?
Yes
Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION [LF, L3].)
No
Go to the next step.
12
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [LF ATX (FN4A-EL), L3 ATX].)
No
Troubleshooting completed.