DTC P0071:00 [MZR-CD 2.2]
id0102f3145800
|
DTC P0071:00 |
Exhaust gas pressure correction temperature sensor circuit range/performance malfunction |
|---|---|
|
DETECTION CONDITION
|
• The PCM monitors the temperature from exhaust gas pressure correction temperature sensor signal. If the temperature is less than 13 °C {55 °F}, the PCM determines that there is a malfunction in exhaust gas pressure correction temperature sensor.
Diagnostic support note
• The MIL does not illuminate.
• The DTC is stored in the PCM memory.
|
|
POSSIBLE CAUSE
|
• Exhaust gas pressure correction temperature sensor connector or terminal malfunction
• Exhaust gas pressure correction temperature sensor malfunction
• PCM connector or terminal malfunction
• PCM malfunction
|
Diagnostic procedure
|
STEP |
INSPECTION |
ACTION |
|
|---|---|---|---|
|
1
|
VERIFY FREEZE FRAME DATA (MODE2) OR SNAPSHOT DATA HAVE BEEN RECORDED
• Have FREEZE FRAME DATA (mode2) or snapshot data been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA (mode2) and snapshot data on the repair order, then go to the next step.
|
||
|
2
|
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
• Verify related Service Information availability.
• Is any related Service Information available?
|
Yes
|
Perform repair or diagnosis according to the available Service Information.
• If the vehicle is not repaired, go to the next step.
|
|
No
|
Go to the next step.
|
||
|
3
|
VERIFY CURRENT SIGNAL STATUS: IS CONCERN INTERMITTENT OR CONSTANT?
• Clear the DTC from the PCM memory using the M-MDS.
• Start the engine.
• Perform the DTC Reading Procedure.
• Is the same DTC present?
|
Yes
|
Go to the next step.
|
|
No
|
Intermittent concern exists.
Perform the “INTERMITTENT CONCERN TROUBLESHOOTING”.
|
||
|
4
|
INSPECT EXHAUST GAS PRESSURE CORRECTION TEMPERATURE SENSOR CONNECTOR FOR POOR CONNECTION
• Switch the ignition to off.
• Disconnect the exhaust gas pressure correction temperature sensor connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the terminal, then go to Step 7.
|
|
No
|
Go to the next step.
|
||
|
5
|
INSPECT EXHAUST GAS PRESSURE CORRECTION TEMPERATURE SENSOR
• Inspect the exhaust gas pressure correction temperature sensor.
• Is there any malfunction?
|
Yes
|
Replace the exhaust gas pressure correction temperature sensor, then go to Step 7.
|
|
No
|
Go to the next step.
|
||
|
6
|
INSPECT PCM CONNECTOR FOR POOR CONNECTION
• Switch the ignition to off.
• Disconnect the PCM connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the terminal, then go to the next step.
|
|
No
|
Go to the next step.
|
||
|
7
|
VERIFY TROUBLESHOOTING OF DTC P0071:00 COMPLETED
• Make sure to reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Start the engine.
• Perform the DTC Reading Procedure.
• Is the same DTC present?
|
Yes
|
Repeat the inspection from Step 1.
• If the malfunction recurs, replace the PCM.
Go to the next step.
|
|
No
|
Go to the next step.
|
||
|
8
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the “AFTER REPAIR PROCEDURE”.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [MZR-CD 2.2].)
|
|
No
|
DTC troubleshooting completed.
|
||