DTC P2610:00 [SKYACTIV-G 2.0]

id0102h1303800

DTC P2610:00

Instrument cluster internal engine off timer performance problem

DETECTION CONDITION

•  Instrument cluster internal engine off timer is damaged.

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.

•  PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle.

•  FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

•  The DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

—

POSSIBLE CAUSE

•  Instrument cluster power supply circuit malfunction (In this case, the instrument cluster records DTC U3003:16.)

•  Instrument cluster internal engine off timer malfunction

•  PCM malfunction

SYSTEM WIRING DIAGRAM

—

DTC P2610:00	Instrument cluster internal engine off timer performance problem
DETECTION CONDITION	• Instrument cluster internal engine off timer is damaged. Diagnostic support note • This is a continuous monitor (CCM). • The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM. • PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • The DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	—
POSSIBLE CAUSE	• Instrument cluster power supply circuit malfunction (In this case, the instrument cluster records DTC U3003:16.) • Instrument cluster internal engine off timer malfunction • PCM malfunction
SYSTEM WIRING DIAGRAM	—

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY FUSE INSTALLATION CONDITION BETWEEN INSTRUMENT CLUSTER AND BATTERY • Verify the fuse installation condition between the instrument cluster and battery. • Is each fuse installed correctly?	Yes	Inspect the fuse between instrment cluster and battery. • If the fuse is blown: ― Repair or replace the wiring harness for a possible short to ground, then go to Step 5. ― Replace the fuse. • If the fuse is deteriorated: ― Replace the fuse, then go to Step 5. • If the fuse is normal: ― Go to the next step.
3		No	Install the fuse, then go to Step 5.
4	VERIFY STORED DTC IN INSTRUMENT CLUSTER • Switch the ignition to off, then to ON (engine off). • Retrieve the instrument cluster DTC using the M-MDS. (See DTC INSPECTION [INSTRUMENT CLUSTER].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [INSTRUMENT CLUSTER].)
4		No	Replace the instrument cluster, then go to the next step. (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
5	VERIFY DTC TROUBLESHOOTING COMPLETED Note • DTC P2610:00 can be cleared by performing the engine start and stop procedure. • Start the engine. • Stop the engine. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [SKYACTIV-G 2.0].) • Start the engine and warm it up completely. • Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 2.0].) • Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)
5		No	Go to the next step.
6	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [SKYACTIV-G 2.0].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-G 2.0].)
6		No	DTC troubleshooting completed.