DTC C0062:76 [DYNAMIC STABILITY CONTROL (DSC)]

id0402b2901000

DTC

C0062:76

SAS control module system

DETECTION CONDITION

•  Error is detected in communication with SAS control module by CAN communication (CAN2).

POSSIBLE CAUSE

•  Poor SAS control module installation

•  Low-G sensor malfunction in SAS control module

STEP

INSPECTION

ACTION

1

VERIFY IF THE VEHICLE HAS BEEN DRIVEN ON A CHASSIS DYNAMOMETER BEFORE

•  Has the vehicle ever been driven on a chassis dynamometer?

Yes

Go to Step 4.

No

Go to the next step.

2

VERIFY IF SAS CONTROL MODULE IS CORRECTLY INSTALLED

•  Verify installation condition of SAS control module.

•   Is the installation condition normal?

Yes

Go to the next step.

No

Install the SAS control module correctly, then go to the next step.

3

INSPECT SAS CONTROL MODULE MALFUNCTION

•  Switch the ignition to off.

•  Using the M-MDS, perform the DTC inspection for the SAS control module.
(See DTC INSPECTION.)

•  Are any DTCs detected?

Yes

Go to applicable DTC inspection.

(See DTC TABLE.)

No

Perform DSC sensor initialization.

(See DSC SENSOR INITIALIZATION PROCEDURE.)

After initializing the DSC sensor, go to the next step.

4

VERIFY THAT THE SAME DTC IS NOT PRESENT

•  Clear the DTCs from the memory.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)

•  Are the same DTCs present?

Yes

Repeat the inspection from Step 1.

If the malfunction recurs, replace the DSC HU/CM, then go to the next step.

(See DSC HU/CM REMOVAL/INSTALLATION.)

No

Go to the next step.

5

VERIFY THAT NO OTHER DTCS ARE PRESENT

•  Are any other DTCs output?

Yes

Go to the applicable DTC inspection.

(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)

No

DTC troubleshooting completed.

DTC	C0062:76		SAS control module system
DETECTION CONDITION		• Error is detected in communication with SAS control module by CAN communication (CAN2).
POSSIBLE CAUSE		• Poor SAS control module installation • Low-G sensor malfunction in SAS control module

STEP	INSPECTION		ACTION
1	VERIFY IF THE VEHICLE HAS BEEN DRIVEN ON A CHASSIS DYNAMOMETER BEFORE • Has the vehicle ever been driven on a chassis dynamometer?	Yes	Go to Step 4.
1		No	Go to the next step.
2	VERIFY IF SAS CONTROL MODULE IS CORRECTLY INSTALLED • Verify installation condition of SAS control module. • Is the installation condition normal?	Yes	Go to the next step.
2		No	Install the SAS control module correctly, then go to the next step.
3	INSPECT SAS CONTROL MODULE MALFUNCTION • Switch the ignition to off. • Using the M-MDS, perform the DTC inspection for the SAS control module. (See DTC INSPECTION.) • Are any DTCs detected?	Yes	Go to applicable DTC inspection. (See DTC TABLE.)
3		No	Perform DSC sensor initialization. (See DSC SENSOR INITIALIZATION PROCEDURE.) After initializing the DSC sensor, go to the next step.
4	VERIFY THAT THE SAME DTC IS NOT PRESENT • Clear the DTCs from the memory. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].) • Are the same DTCs present?	Yes	Repeat the inspection from Step 1. If the malfunction recurs, replace the DSC HU/CM, then go to the next step. (See DSC HU/CM REMOVAL/INSTALLATION.)
4		No	Go to the next step.
5	VERIFY THAT NO OTHER DTCS ARE PRESENT • Are any other DTCs output?	Yes	Go to the applicable DTC inspection. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)
5		No	DTC troubleshooting completed.