DTC B1081:71, B1082:71 [FULL-AUTO AIR CONDITIONER]
id0702c1816500
DTC B1081:71 |
• Driver-side air mix actuator motor lock (L.H.D.)
• Passenger-side air mix actuator motor lock (R.H.D.)
|
---|---|
DTC B1082:71 |
• Passenger-side air mix actuator motor lock (L.H.D.)
• Driver-side air mix actuator motor lock (R.H.D.)
|
POSSIBLE CAUSE
|
• Connector or terminal malfunction
• Air mix actuator malfunction
• A/C unit (air mix link and air mix crank) malfunction
• Open circuit in wiring harness between climate control unit connector terminal 1U and 1W (Driver-side)
• Open or short circuit in wiring harness between climate control unit connector terminal 1S and 1Q (Passenger-side)
• Short to ground in wiring harness between climate control unit connector terminal 1U and 1W (Driver-side)
• Short to ground in wiring harness between climate control unit connector terminal 1S and 1Q (Passenger-side)
• Climate control unit malfunction
|
![]() |
|
![]() |
Diagnostic procedure
STEP |
INSPECTION |
ACTION |
|
---|---|---|---|
1
|
INSPECT AIR MIX ACTUATOR CONNECTOR
• Switch the ignition to off.
• Disconnect the negative battery cable.
• Disconnect the air mix actuator connector.
• Inspect the connector and terminals (corrosion, damage, pin disconnection).
• Are the connector and terminals normal?
|
Yes
|
Go to the next step.
|
No
|
Repair/replace the connector or terminal.
After repair procedure, go to the next step.
|
||
2
|
INSPECT AIR MIX ACTUATOR OPERATION
• Disconnect the air mix actuator connector.
• Apply battery positive voltage and connect the ground to the air mix actuator terminals B and C, and then inspect the air mix actuator.
• Does the air mix actuator operate?
|
Yes
|
Connect the connector, then go to Step 4.
|
No
|
Go to the next step.
|
||
3
|
INSPECT AIR MIX LINK OPERATION
• Remove the air mix actuator.
• Operate the air mix link manually.
• Does the air mix link operate smoothly?
|
Yes
|
Replace the air mix actuator.
Go to the next step.
|
No
|
Replace the air mix link and the air mix crank.
Go to the next step.
|
||
4
|
INSPECT AIR MIX ACTUATOR CIRCUIT FOR OPEN CIRCUIT OR SHORT TO GROUND
• Disconnect the climate control unit connector.
• Apply battery positive voltage and connect the ground to the climate control unit terminal 1W and 1U, and then inspect the air mix actuator. (Driver-side)
• Apply battery positive voltage and connect the ground to the climate control unit terminal 1S and 1Q, and then inspect the air mix actuator. (Passenger-side)
• Does the air mix actuator operate?
|
Yes
|
Go to the next step.
|
No
|
Repair/replace the malfunctioning vehicle wiring harness.
After repair procedure, go to the next step.
|
||
5
|
VERIFY CLIMATE CONTROL UNIT CONNECTOR CONDITION
• Inspect the connector and terminals (corrosion, damage, pin disconnection).
• Are the connector and terminals normal?
|
Yes
|
Go to the next step.
|
No
|
Repair/replace the malfunctioning vehicle wiring harness, connector, or terminal.
After repair procedure, go to the next step.
|
||
6
|
VERIFY THAT SAME DTC IS NOT OUTPUT AGAIN
• Reconnect the disconnected connectors.
• Connect the negative battery cable.
• Clear the past malfunction from memory.
• Verify DTCs.
• Is DTC B1081:71 or B1082:71 output?
|
Yes
|
Repeat the inspection from Step 1.
• If the malfunction does not recur, go to the next step.
• If the malfunction recurs, replace the climate control unit.
Go to the next step.
|
No
|
Go to the next step.
|
||
7
|
VERIFY THAT NO OTHER DTCs ARE PRESENT
• Verify other DTCs displayed.
• Are any other DTCs output?
|
Yes
|
Perform the corresponding DTC inspection.
|
No
|
DTC troubleshooting completed.
|