POWER WINDOW MOTOR INSPECTION

id091200417000


Front Driver Side

1.  Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [MZR 2.0, MZR 2.5].) (See BATTERY REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].) (See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI i-stop].) (See BATTERY REMOVAL/INSTALLATION [MZ-CD 1.6].) (See BATTERY REMOVAL/INSTALLATION [MZR-CD 2.2].) (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0].) (See BATTERY REMOVAL/INSTALLATION [MZR 1.5, MZR 1.6].)

2.  Remove the inner garnish. (See INNER GARNISH REMOVAL/INSTALLATION.)

3.  Remove the front door trim. (See FRONT DOOR TRIM REMOVAL/INSTALLATION.)

4.  Disconnect the power window motor connector.

5.  Apply battery positive voltage and connect the ground to power window motor terminals E and F, and then inspect the power window motor operation.

am3zzw00012324

•  If the power window motor does not operate as indicated in the table, replace the power window motor.

Operation

Terminal

E

F
Open
Ground
B+
Close
B+
Ground

6.  Connect the battery positive voltage to power window motor terminal D and connect terminal C to ground.

7.  Operate the power window motor and measure the voltage at terminals A and B.

•  If there is any malfunction, replace the power window motor.
Voltage
Pulse: max. 5 V/min. 0 V


Front Passenger Side

1.  Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [MZR 2.0, MZR 2.5].) (See BATTERY REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].) (See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI i-stop].) (See BATTERY REMOVAL/INSTALLATION [MZ-CD 1.6].) (See BATTERY REMOVAL/INSTALLATION [MZR-CD 2.2].) (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0].) (See BATTERY REMOVAL/INSTALLATION [MZR 1.5, MZR 1.6].)

2.  Remove the inner garnish. (See INNER GARNISH REMOVAL/INSTALLATION.)

3.  Remove the front door trim. (See FRONT DOOR TRIM REMOVAL/INSTALLATION.)

4.  Disconnect the power window motor connector.

5.  Apply battery positive voltage and connect the ground to power window motor terminals E and F, and then inspect the power window motor operation.

am3uuw00005138

•  If the power window motor does not operate as indicated in the table, replace the power window motor.

Operation

Terminal

E

F
Open
Ground
B+
Close
B+
Ground


Rear

1.  Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [MZR 2.0, MZR 2.5].) (See BATTERY REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].) (See BATTERY REMOVAL/INSTALLATION [MZR 2.0 DISI i-stop].) (See BATTERY REMOVAL/INSTALLATION [MZ-CD 1.6].) (See BATTERY REMOVAL/INSTALLATION [MZR-CD 2.2].) (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0].) (See BATTERY REMOVAL/INSTALLATION [MZR 1.5, MZR 1.6].)

2.  Remove the rear door trim. (See REAR DOOR TRIM REMOVAL/INSTALLATION.)

3.  Disconnect the power window motor connector.

4.  Apply battery positive voltage and connect the ground to power window motor terminals E and F, and then inspect the power window motor operation.

am3uuw00005138

•  If the power window motor does not operate as indicated in the table, replace the power window motor.

Operation

Terminal

E

F
Open
Ground
B+
Close
B+
Ground