DTC U2005:68 [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)]

• The SRS air bag system can be identified by whether or not the seat track position sensor is present.

― Standard deployment control system: Without seat track position sensor

― Two-step deployment control system: With seat track position sensor

System malfunction location	PCM communication error (vehicle speed signal)
Detection condition	• SAS control module receives vehicle speed signal error from the PCM for 5 s or more with the ignition switched ON (engine off or on).
Fail-safe	Not applicable
Possible cause	• PCM malfunction • SAS control module malfunction
System wiring diagram	Not applicable

System malfunction location

PCM communication error (vehicle speed signal)

Detection condition

• SAS control module receives vehicle speed signal error from the PCM for 5 s or more with the ignition switched ON (engine off or on).

Fail-safe

Not applicable

Possible cause

• PCM malfunction

• SAS control module malfunction

System wiring diagram

Not applicable

Step	Inspection	Action
1	VERIFY SAS CONTROL MODULE DTCs AGAIN • Clear SAS control module DTCs using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].) • Switch the ignition ON (engine off or on) and wait for 5 s or more. • Perform the SAS control module DTC inspection using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].) • Is the same Pending DTC present?	Yes	Go to the next step.
No	Go to Step 5.
2	VERIFY PCM DTCs • (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].) (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5T)].) (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION))].) (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION))].) • Is the DTC displayed?	Yes	Repair the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [PCM (SKYACTIV-D 2.2)].) (See DTC TABLE [PCM (SKYACTIV-G 2.5T)].) (See DTC TABLE [PCM (SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION))].) (See DTC TABLE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION))].)
No	Go to the next step.
3	PERFORM DTC INSPECTION AND VERIFY IF MALFUNCTIONING PART IS PCM • Clear SAS control module DTCs using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].) • Switch the ignition ON (engine off or on) and wait for 5 s or more. • Perform the SAS control module DTC inspection using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].) • Is the same Pending DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.5T].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION)].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
No	Go to Step 5.
4	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Clear SAS control module DTCs using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].) • Switch the ignition ON (engine off or on) and wait for 5 s or more. • Perform the SAS control module DTC inspection using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].) • Is the same Pending DTC present?	Yes	Replace the SAS control module, then go to the next step. (See SAS CONTROL MODULE REMOVAL/INSTALLATION [STANDARD DEPLOYMENT CONTROL SYSTEM].)
No	Go to the next step.
5	VERIFY IF OTHER DTCs DISPLAYED • Are any other DTCs displayed?	Yes	Repair the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].)
No	DTC troubleshooting completed.

Step

Inspection

Action

VERIFY SAS CONTROL MODULE DTCs AGAIN

• Clear SAS control module DTCs using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].)

• Switch the ignition ON (engine off or on) and wait for 5 s or more.

• Perform the SAS control module DTC inspection using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].)

• Is the same Pending DTC present?

Yes

Go to the next step.

Go to Step 5.

VERIFY PCM DTCs

• (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].)

(See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5T)].)

(See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION))].)

(See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION))].)

• Is the DTC displayed?

Yes

Repair the malfunctioning part according to the applicable DTC troubleshooting.

(See DTC TABLE [PCM (SKYACTIV-D 2.2)].)

(See DTC TABLE [PCM (SKYACTIV-G 2.5T)].)

(See DTC TABLE [PCM (SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION))].)

(See DTC TABLE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION))].)

Go to the next step.

PERFORM DTC INSPECTION AND VERIFY IF MALFUNCTIONING PART IS PCM

• Clear SAS control module DTCs using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].)

• Switch the ignition ON (engine off or on) and wait for 5 s or more.

• Perform the SAS control module DTC inspection using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].)

• Is the same Pending DTC present?

Yes

Replace the PCM, then go to the next step.

(See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.5T].)

(See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION)].)

(See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)].)

(See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

Go to Step 5.

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

• Clear SAS control module DTCs using the M-MDS. (See CLEARING DTC [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].)

• Switch the ignition ON (engine off or on) and wait for 5 s or more.

• Perform the SAS control module DTC inspection using the M-MDS. (See DTC INSPECTION [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].)

• Is the same Pending DTC present?

Yes

Replace the SAS control module, then go to the next step. (See SAS CONTROL MODULE REMOVAL/INSTALLATION [STANDARD DEPLOYMENT CONTROL SYSTEM].)

Go to the next step.

VERIFY IF OTHER DTCs DISPLAYED

• Are any other DTCs displayed?

Yes

Repair the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [SAS CONTROL MODULE (STANDARD DEPLOYMENT CONTROL SYSTEM)].)

DTC troubleshooting completed.