PID/DATA MONITOR INSPECTION (EXCEPT FOR GENERAL (L.H.D.) SPECS. SPORT AT) [FN4A-EL]

1. Connect the WDS or equivalent to the DLC-2.

2. Measure the PID value.

Note

• Perform part inspection for the output device after PCM inspection.

• The PID/DATA MONITOR function monitors the calculated value of the input/output signals in the PCM. Therefore, if a monitored value of an output device is out of specification, it is necessary to inspect the monitored value of the input device related to the output device control. Since an output device malfunction is not directly indicated as a malfunction of the monitored value for the output device, it is necessary to inspect the output device individually using the simulation function.

PID/DATA MONITOR AND RECORD function table

Monitor item (Definition)	Unit/Condition		Condition/Specification	Action	PCM terminal
DWN SW	ON/OFF		M range, down shift: ON Other: OFF	Inspect selector lever component. (See SELECTOR LEVER COMPONENT INSPECTION (SPORT AT).)	3K
GEAR	-		1GR: 1 2GR: 2 3GR: 3 4GR: 4	Inspect following PIDs: SSA/SS1, SSB/SS2, SSC/SS3, SSD/SS4, SSE/SS5	3P, 3S, 3Y, 4Y, 4AB, 4AC
LINEDES	kPa	inHg	Indicates target line pressure	Inspect following PIDs: TFT, TFT V, VPWR, TP, TSS, VSS, TROD, TRD, TRL, PNP	3V, 3Y
LPS (Pressure control solenoid)	%		Change current value according to throttle opening angle	Inspect pressure control solenoid. (See SOLENOID VALVE INSPECTION [FN4A-EL].)	3V, 3Y
MNL SW	ON/OFF		M range: ON Other: OFF	Inspect selector lever component. (See SELECTOR LEVER COMPONENT INSPECTION (SPORT AT).)	3Q
OP SW B (Oil pressure switch)	ON/OFF		1, 2 or 3GR: ON Other: OFF	Inspect oil pressure switch inspection. (See OIL PRESSURE SWITCH INSPECTION [FN4A-EL].)	3T
SSA/SS1 (Shift solenoid A)	%		4GR: 99% others: 0%	Inspect shift solenoid A. (See SOLENOID VALVE INSPECTION [FN4A-EL].)	4AB
SSB/SS2 (Shift solenoid B)	%		1GR at D range: 99% Others: 0%	Inspect shift solenoid B. (See SOLENOID VALVE INSPECTION [FN4A-EL].)	4AC
SSC/SS3 (Shift solenoid C)	%		1GR/2GR: 99% Others: 0%	Inspect shift solenoid C. (See SOLENOID VALVE INSPECTION [FN4A-EL].)	4Y
TCS (HOLD switch)	ON/OFF		HOLD switch pressed: ON HOLD switch released: OFF	Inspect HOLD switch. (See HOLD SWITCH INSPECTION (4AT) [FN4A-EL].)	3Q
TFT (Transaxle fluid temperature)	°C	°F	Indicates transaxle fluid temperature	Inspect TFT sensor. (See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR INSPECTION [FN4A-EL].)	3D
TFTV (Transaxle fluid signal voltage)	V		ATF 20 °C {68 °F}: 3.4-3.6 V ATF 130 °C {266 °F}: 0.4-0.5 V	Inspect TFT sensor. (See TRANSAXLE FLUID TEMPERATURE (TFT) SENSOR INSPECTION [FN4A-EL].)	3D
THOP (Throttle position sensor)	%		CTP: 0% WOT:100%	Inspect TP sensor. (See THROTTLE POSITION (TP) SENSOR INSPECTION [LF, L3].)	2A
TP (Throttle position sensor signal voltage)	V		CTP: 0.4-1.5 V WOT: 4.0-5.0 V	Inspect TP sensor. (See THROTTLE POSITION (TP) SENSOR INSPECTION [LF, L3].)	2A
TR (Transaxle range)	-		P position: P R position: R N position: N D range: D S range: S L range: L	Inspect TR switch. (See TRANSAXLE RANGE (TR) SWITCH INSPECTION [FN4A-EL].)	1W
TR SENS (TR switch)	V		P position: 4.34-4.79 V R position: 3.83-4.18 V N position: 3.05-3.50 V D range: 2.23-2.66 V S range: 1.46-1.84 V L range: 0.80-1.09 V	Inspect TR switch. (See TRANSAXLE RANGE (TR) SWITCH INSPECTION [FN4A-EL].)	1W
TSS (Input/turbine speed)	rpm		Ignition switch ON: 0 rpm Idle: 700-800 rpm (P, N position) Indicates Input/turbine speed	Inspect input/turbine speed sensor. (See INPUT/TURBINE SPEED SENSOR INSPECTION [FN4A-EL].)	3G, 3J
UP SW	ON/OFF		M range, up shift: ON Other: OFF	Inspect selector lever component. (See SELECTOR LEVER COMPONENT INSPECTION (SPORT AT).)	3N
VPWR (Battery positive voltage)	V		Ignition switch ON: B+ Engine running: B+	Inspect main relay. (See RELAY INSPECTION.) Inspect buttery. (See BATTERY INSPECTION [LF, L3].)	2Y, 2Z
VSS (Vehicle speed)	km/h	mph	Indicates vehicle speed	Inspect VSS. (See VEHICLE SPEEDOMETER SENSOR (VSS) INSPECTION (WITHOUT ABS) [FN4A-EL].)	3C