DTC P2428:00 [MZR-CD (RF Turbo)]


id0102f1153500

DTC P2428:00

Exhaust gas temperature too high

DETECTION CONDITION
•  The PCM monitors the diesel particulate filter temperature using the exhaust gas temperature sensor middle and lower signal after the diesel particulate filter regeneration procedure. If the PCM detects the exhaust gas temperature more than 1,000 °C {1,832 °F}, the PCM determines that the exhaust gas temperature too high.
Diagnostic support note
•  The FREEZE FRAME DATA is not available.
•  The DTC is stored in the PCM memory.
POSSIBLE CAUSE
•  Exhaust gas pressure sensor malfunction
•  Exhaust gas temperature sensor (middle) malfunction
•  Exhaust gas temperature sensor (lower) malfunction
•  Diesel particulate filter malfunction
•  PCM malfunction

Diagnostic procedure

STEP

INSPECTION

ACTION

1
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
•  Has FREEZE FRAME DATA been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2
VERIFY RELATED SERVICE INFORMATION
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to available Service Information.
•  If vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY OTHER STORED DTCS
•  Connect the M-MDS to DLC-2.
•  Switch the ignition to ON.
•  Retrieve the stored DTC.
•  Is the DTC P2458 or P242F displayed?
Yes
Go to the appropriate DTC troubleshooting procedures.
No
Go to the next step.
4
INSPECT EXHAUST GAS PRESSURE SENSOR HOSE CONNECTION
•  Visually inspect the exhaust gas pressure sensor hose connection.
•  Are the hoses connected properly?
Yes
Go to the next step.
No
Reconnect hoses properly, then go to Step 14.
5
INSPECT EXHAUST GAS PRESSURE SENSOR
•  Inspect the exhaust gas pressure sensor.
•  Is it normal?
Yes
Go to the next step.
No
Repair or replace suspected part, then go to Step 14.
6
INSPECT CHARACTER FOR SENSORS
•  Inspect character for following sensors.
―  Exhaust gas temperature sensors (upper, middle, lower)
―  Exhaust gas pressure sensor
―  A/F sensor
•  Are characters normal?
Yes
Go to the next step.
No
Replace the abnormal part.
Perform the fuel injection learning, then go to Step 14.
7
INSPECT ENGINE COMPRESSION
•  Inspect engine compression.
•  Is it normal?
Yes
Go to the next step.
No
Perform engine overhaul for repairs, then go to the next step.
8
VISUALLY INSPECT CKP SENSOR
•  Visually inspect for CKP sensor and CKP sensor pulse wheel.
•  Is there any problem?
Yes
Repair or replace suspected part.
Perform the fuel injection learning, then go to Step 14.
No
Go to the next step.
9
INSPECT EGR VALVE OPERATION
•  Perform EGR Valve Operation Inspection.
•  Does the EGR valve work properly?
Yes
Go to the next step.
No
Repair or replace malfunctioning part according to inspection results.
Perform the fuel injection learning, then go to Step 14.
10
VISUALLY INSPECT A/F SENSOR AND EXHAUST GAS TEMPERATURE SENSOR (LOWER)
•  Remove and visually inspect the A/F sensor and exhaust gas temperature sensor (lower).
•  Is there any white or melted on tip?
Yes
Replace suspect sensor, then go to the next step.
No
Perform the fuel injection learning, then go to Step 14.
11
VISUALLY INSPECT DIESEL PARTICULATE FILTER
•  Visually inspect the diesel particulate filter.
•  Is there any damaged or deterioration (white)?
Yes
Replace the oxidation catalytic converter, then go to the next step.
No
Perform the fuel injection learning, then go to Step 14.
13
RETRIEVE DTC
•  Retrieve any DTC using the M-MDS.
•  Is DTC P2428:00 detected?
Yes
Return to Step 1.
No
Go to the next step.
14
VERIFY TROUBLESHOOTING OF DTC P2428:00 COMPLETED
•  Make sure to reconnect all disconnected connectors.
•  Switch the ignition to ON (engine off).
•  Clear the DTC from PCM memory using the M-MDS.
•  Start the engine.
•  Is the same DTC present?
Yes
Replace the PCM, go to the next step.
No
Go to the next step.
15
VERIFY AFTER REPAIR PROCEDURE
•  Perform “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
No
Troubleshooting completed.