NO.2 ANY OF THE FOLLOWING LIGHTS REMAIN ON: (ABS WARNING LIGHT, BRAKE SYSTEM WARNING LIGHT, DSC INDICATOR LIGHT AND/OR DSC OFF LIGHT) [DYNAMIC STABILITY CONTROL (DSC)]

id0403b2804600

2
Any of the following lights remain on: (ABS warning light, BRAKE system warning light, DSC indicator light and/or DSC OFF light)
[TROUBLESHOOTING HINTS]
•  Brake fluid amount is low
•  Parking brake does not release
•  Improper brake switch signal input to PCM (the brake system warning light (vehicle without the malfunction warning light) / malfunction warning light (vehicle equipped with the malfunction warning light) illuminate)*
•  No connection at DSC HU/CM connector
(When DSC HU/CM connector is disconnected, ABS warning light and BRAKE system warning light illuminate)
•  DSC HU/CM detected malfunction (Input and output device malfunction)
•  DSC HU/CM detects low voltage in power supply
•  DSC HU/CM ground malfunction
(When DSC HU/CM ground is not securely connected, ABS warning light and BRAKE system warning light illuminate but diagnostic trouble code does not displayed)
•  DSC HU/CM does not operate (DSC HU/CM malfunction)

*  :Applied VIN (assume) FE10**301152—

Diagnostic procedure

STEP

INSPECTION

ACTION
1
INSPECT BRAKE FLUID AMOUNT AND VERIFY THAT PARKING BRAKE RELEASES
•  Is the brake fluid amount normal?
•  Is the parking brake lever released?
Yes
Go to the next step.
No
Add brake fluid or release parking brake lever.
2
INSPECT PCM DTC
•  Perform the PCM ON-BOARD DIAGNOSTIC procedure.
•  Is the DTC P0571 and/or P0703 present?
Yes
Go to the appropriate DTC inspection.
(See DTC P0571 [13B-MSP].)
(See DTC P0703 [13B-MSP].)
No
Go to the next step.
3
INSPECT DTCS IN DSC HU/CM
•  Inspect the DTC for the DSC ON-BOARD DIAGNOSTIC SYSTEM.
•  Have DTCs been stored in memory?
Yes
Perform inspection using appropriate DTC.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)
No
Go to the next step.
4
INSPECT WHETHER MALFUNCTION IS IN CONTROL MODULE CONNECTOR, TERMINAL OR OTHER
•  Do ABS warning light and BRAKE system warning light go off after 4 s when the ignition switch is turned to the ON position?
Yes
Temporary poor connection in control module connector.
Inspect DSC HU/CM connector, then go to Step 7.
Inspect DSC HU/CM connector terminal, then go to Step 8.
No
Go to the next step.
5
INSPECT BATTERY
•  Is the battery voltage normal?
Yes
Go to the next step.
No
Inspect the battery and charging system.
(See BATTERY INSPECTION [13B-MSP].)
(See GENERATOR INSPECTION [13B-MSP].)
6
INSPECT CHARGING SYSTEM
•  Is the battery voltage normal with electrical load (A/C, headlight, etc.) on and engine idling?
Yes
Go to the next step.
No
Inspect the charging system (drive belt tension, generator, etc.).
(See GENERATOR INSPECTION [13B-MSP].)
7
VERIFY THAT DSC HU/CM CONNECTOR IS CONNECTED
•  Is the DSC HU/CM securely connected?
Yes
Go to the next step.
No
Connect the DSC HU/CM connector securely, then go to the next step.
8
VERIFY THAT DSC HU/CM CONNECTOR TERMINAL OR RELATED CONNECTOR TERMINALS ARE CONNECTED
•  Are DSC HU/CM connector terminal or instrument cluster connector terminal etc. related connector terminals securely connected?
Yes
Replace the DSC HU/CM.
(See DSC HU/CM REMOVAL/INSTALLATION.)
No
Securely connect the DSC HU/CM connector terminal and related connector terminals.