Reassembly

SEAT: FRONT SEAT ASSEMBLY: REASSEMBLY

1. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY (w/o Lumbar Support)

(a) Install the separate type front seatback assembly with the 4 bolts.

Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)

2. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY (w/ Lumbar Support)

(a) Install the separate type front seatback assembly with the 4 bolts.

Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)

3. INSTALL SEAT POSITION SENSOR Installation

4. INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side) Installation

5. INSTALL FRONT SEAT WIRE (w/ Lumbar Support)

(a) Engage the 2 clamps and install the front seat wire.

(b) Connect the connector.

6. INSTALL NO. 1 FRONT SEAT CUSHION PROTECTOR

(a) Engage the 2 guides and install the No. 1 front seat cushion protector with the screw.

7. INSTALL NO. 2 FRONT SEAT CUSHION PROTECTOR

(a) Engage the 2 guides and install the No. 2 front seat cushion protector with the screw.

8. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (w/ Vertical Adjuster)

(a) Engage the clip and install the screw.

(b) Engage the hook and install the front seat lower cushion shield RH as shown in the illustration.

9. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjuster)

(a) Engage the clip and install the screw.

(b) Engage the hook and install the front seat lower cushion shield LH as shown in the illustration.

10. INSTALL RECLINING ADJUSTER INSIDE COVER RH

(a) Engage the guide and install the reclining adjuster inside cover RH.

11. INSTALL RECLINING ADJUSTER INSIDE COVER LH

(a) Engage the guide and install the reclining adjuster inside cover LH.

12. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

(a) Using hog ring pliers, install 2 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(b) Using hog ring pliers, install 5 new hog rings

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
13. INSTALL FRONT SEATBACK COVER WITH PAD

(a) Install the front seatback cover bracket with the nut.

Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)

NOTICE:
* For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
* Check that the strap is not twisted after installing the bracket.
* Install the bracket securely.
(b) Engage the 4 claws and install the 2 front seat headrest supports.

(c) Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 3 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
14. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

(a) Using hog ring pliers, install 11 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(b) Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
15. INSTALL FRONT SEAT CUSHION COVER WITH PAD

(a) Engage each hook as shown in the illustration.

(b) Engage the 2 hooks as shown in the illustration.

NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, take care to minimize wrinkles as much as possible.
(d) for Passenger Side:

(1) Engage the guide and install the belt warning occupant detection sensor.

(2) Engage the 3 clamps.

(3) Connect the connector.

(e) Engage the 4 hooks.

(f) w/ Seat Heater System:

(1) Engage the clamp.

(2) Fasten the front seat cushion cover with pad as shown in the illustration.

(3) Connect the connector.

(g) w/ Lumber support:

(1) Engage the 4 clamps.

(2) Engage the 3 clamps and connect the connector.

(h) Engage the hook and install the front seat cushion cover with pad.

16. INSTALL FRONT SEAT CUSHION INNER SHIELD

(a) Engage the 2 claws and install the front seat cushion inner shield.

17. INSTALL FRONT SEAT INNER BELT ASSEMBLY Installation

18. INSTALL LUMBAR SWITCH (w/ Lumbar Support)

(a) Install the lumbar switch with the 2 screws.

19. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY

(a) w/ Lumber Support:

(1) Disengage the 5 clamps.

(2) Connect the connector.

(b) Engage the clip and 2 claws.

(c) Install the front seat cushion shield assembly with the screw.

20. INSTALL VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)

(a) Install the vertical adjusting handle with the screw.

21. INSTALL RECLINING ADJUSTER RELEASE HANDLE

(a) Engage the claw and install the reclining adjuster release handle.