DTC B0072[1A] Pretensioner(Front Left) Circuit Low Resistance (Air Bag (Driver/Passenger))

1. SRS system check

Refer to "58.SRS Control 8A.Troubleshooting(Air Bag (Driver/Passenger)) diagnostic system check-SRS controls".

2. Front left side pretensioner circuit resistance check

1) Observe the Pretensioner(Front Left) Loop Resistance parameter on the scan tool. Is the Pretensioner(Front Left) Loop Resistance parameter less than or equal to the specified value?

Value: 1 Ω

Yes (Extend cab models)

=>Go to Intermediate connector connection check.

Yes (Except extend cab models)

=>Go to Connection check for front left side pretensioner harness connector.

No

Go to Intermittent conditions of SRS control.

Refer to "209.Restraints 22D.Symptom Intermittent conditions of SRS control".

3. Intermediate connector connection check

1) Turn OFF the ignition switch for 15 seconds or more.

2) Verify that the intermediate connector (H39) is securely connected. Is the intermediate connector (H39) securely connected?

Refer to "LHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to Intermediate connector inspection.

No

Securely connect the intermediate connector (H39).

=>Go to Repair verification.

4. Intermediate connector inspection

1) Disconnect the intermediate connector (H39).

2) Inspect the intermediate connector terminals (pins 2 and 3 of H39) for bending, dirt, etc. Is the result normal?

Refer to "LHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to Current DTC check.

No

Repair the connections as necessary.

=>Go to Repair verification.

5. Connection check for front left side pretensioner harness connector

1) Connect the intermediate connector (H39). (Extend cab models)

2) Verify that the front left side pretensioner harness connector (R19 for regular cab and crew cab models, D29 for extend cab models) is securely connected. Is the front left side pretensioner harness connector (R19 for regular cab and crew cab models, D29 for extend cab models) securely connected?

Refer to "LHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to Front left side pretensioner harness connector inspection.

No

Securely connect the front left side pretensioner harness connector (R19 for regular cab and crew cab models, D29 for extend cab models).

=>Go to Repair verification.

6. Front left side pretensioner harness connector inspection

1) Disconnect the front left side pretensioner harness connector (R19 for regular cab and crew cab models, D29 for extend cab models).

2) Inspect the front left side pretensioner harness connector terminals (regular cab and crew cab models: pins 1 and 2 of R19, extend cab models: pins 1 and 2 of D29) for bending, dirt, etc. Is the result normal?

Refer to "LHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to Current DTC check.

No

Repair the connections as necessary.

=>Go to Repair verification.

7. Current DTC check

1) Connect the front left side pretensioner harness connector (R19 for regular cab and crew cab models, D29 for extend cab models).

Refer to "LHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

2) Turn ON the ignition switch.

3) Observe the DTC information with a scan tool for DTC B0072[1A] being set as a current failure. Is a DTC set?

Yes

=>Go to Front left side pretensioner circuit check.

No

=>Go to Repair verification.

8. Front left side pretensioner circuit check

1) Turn OFF the ignition switch for 15 seconds or more.

2) Disconnect the front left side pretensioner harness connector (R19 for regular cab and crew cab models, D29 for extend cab models).

3) Connect the SRS alternative load and the appropriate adapter from the adapter harness kit to the front left side pretensioner harness connector (R19 for regular cab and crew cab models, D29 for extend cab models).

Refer to "LHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).


SST: 5-8840-2857-0 - adapter harness kit


SST: 5-8840-2856-0 - SRS alternative load

4) Turn ON the ignition switch.

5) Observe the DTC information with a scan tool for DTC B0072[1A] being set as a current failure. Is a DTC set?

Yes

=>Go to Inspection for short circuit in front left side pretensioner circuit.

No

Replace the front left side seat belt with pretensioner.

Refer to "8.Restraints 8C.Seat Belt Systems front tongue side seat belt (with pretensioner) (regular cab) removal".

Refer to "8.Restraints 8C.Seat Belt Systems front tongue side seat belt (with pretensioner) (regular cab) installation".

Refer to "8.Restraints 8C.Seat Belt Systems front tongue side seat belt (with pretensioner) (crew cab) removal".

Refer to "8.Restraints 8C.Seat Belt Systems front tongue side seat belt (with pretensioner) (crew cab) installation".

=>Go to Repair verification.

9. Inspection for short circuit in front left side pretensioner circuit

1) Turn OFF the ignition switch for 15 seconds or more.

2) Inspect for a short together between the front left side pretensioner ignition current output (High) circuit and the front left side pretensioner ignition current output (Low) circuit between the SRS control unit (pins 7 and 8 of R5) and the front left side pretensioner (regular cab and crew cab models: pins 1 and 2 of R19, extend cab models: pins 1 and 2 of D29). Is the result normal?

Refer to "LHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Refer to "RHD SRS airbag (Driver/Passenger)" in the ETM (wiring diagram). (Open using the ETM viewer.).

Yes

=>Go to SRS control unit replacement.

No

Repair the circuit as necessary.

=>Go to Repair verification.

10. SRS control unit replacement

Note

  • Perform the VIN programming and ECU lock after replacing the SRS control unit.

Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit removal".

Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit installation".

Refer to "8.Restraints 8Z.Seat Belt and SRS Airbag Electrical Control SRS control unit setting".

Procedure completion

=>Go to Repair verification.

11. Repair verification

1) Reconnect all of the disconnected harness connectors.

2) Clear the DTC with a scan tool.

3) Turn OFF the ignition switch for 15 seconds or more.

4) Turn ON the ignition switch.

5) Observe the DTC information with a scan tool.