NO.6 MASTER WARNING LIGHT ILLUMINATED/MESSAGE RELATED TO VEHICLE SYSTEM MALFUNCTION INDICATED IN DISPLAY [SKYACTIV-D 2.2]

id0103g1831400

6

MASTER WARNING LIGHT ILLUMINATED/MESSAGE RELATED TO VEHICLE SYSTEM MALFUNCTION INDICATED IN DISPLAY

DESCRIPTION

•  Master warning light illuminated.

•  Message related to vehicle system malfunction indicated on the center display. (With center display)

•  Message related to vehicle system malfunction indicated on the LCD in the instrument cluster. (Type A instrument cluster)

POSSIBLE CAUSE

•  PCM DTC is stored.

―  Brake switch malfunction

―  Engine oil level sensor malfunction

―  Glow control module malfunction

―  Glow plug malfunction

•  Blow-by heater relay malfunction

•  Blow-by heater malfunction

•  Timing chain malfunction

•  Instrument cluster malfunction

6	MASTER WARNING LIGHT ILLUMINATED/MESSAGE RELATED TO VEHICLE SYSTEM MALFUNCTION INDICATED IN DISPLAY
DESCRIPTION	• Master warning light illuminated. • Message related to vehicle system malfunction indicated on the center display. (With center display) • Message related to vehicle system malfunction indicated on the LCD in the instrument cluster. (Type A instrument cluster)
POSSIBLE CAUSE	• PCM DTC is stored. ― Brake switch malfunction ― Engine oil level sensor malfunction ― Glow control module malfunction ― Glow plug malfunction • Blow-by heater relay malfunction • Blow-by heater malfunction • Timing chain malfunction • Instrument cluster malfunction

Diagnostic Procedure

STEP

INSPECTION

RESULTS

ACTION

1

VERIFY PCM DTC

•  Retrieve PCM DTCs using the M-MDS.
(See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [PCM (SKYACTIV-D 2.2)].)

No

Go to the next step.

2

INSPECT BLOW-BY HEATER RELAY FOR MALFUNCTION

•  Switch the ignition OFF.

•  Remove the blow-by heater relay.
(See RELAY LOCATION.)

•  Inspect the blow-by heater relay.
(See RELAY INSPECTION.)

•  Is the blow-by heater relay normal?

Yes

Go to the next step.

No

Replace the blow-by heater relay, then go to Step 6.

3

INSPECT BLOW-BY HEATER

•  Inspect the blow-by heater.
(See BLOW-BY HEATER INSPECTION [SKYACTIV-D 2.2].)

•  Is the blow-by heater normal?

Yes

Go to the next step.

No

Replace the blow-by heater, then go to the next step.

(See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

4

INSPECT FOR MALFUNCTION DUE TO DEVIATED VALVE TIMING

•  Inspect the valve timing (timing chain installation condition).
(See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

•  Is the valve timing normal?

Yes

Go to the next step.

No

Adjust the valve timing to the correct timing, then go to Step 6.

5

INSPECT INSTRUMENT CLUSTER

•  Inspect the instrument cluster.
(See INSTRUMENT CLUSTER INSPECTION.)

•  Is the instrument cluster normal?

Yes

Go to the next step.

No

Replace the instrument cluster, then go to the next step.

(See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)

6

Verify the test results.

•  If normal, return to the diagnostic index to service any additional symptoms.
(See SYMPTOM DIAGNOSTIC INDEX [SKYACTIV-D 2.2].)

•  If a malfunction remains, inspect the related Service Information and perform the repair or diagnosis.

―  If the vehicle is repaired, troubleshooting is completed.

―  If the vehicle is not repaired or additional diagnostic information is not available, replace the PCM.
(See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

STEP	INSPECTION	RESULTS	ACTION
1	VERIFY PCM DTC • Retrieve PCM DTCs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [PCM (SKYACTIV-D 2.2)].)
1		No	Go to the next step.
2	INSPECT BLOW-BY HEATER RELAY FOR MALFUNCTION • Switch the ignition OFF. • Remove the blow-by heater relay. (See RELAY LOCATION.) • Inspect the blow-by heater relay. (See RELAY INSPECTION.) • Is the blow-by heater relay normal?	Yes	Go to the next step.
2		No	Replace the blow-by heater relay, then go to Step 6.
3	INSPECT BLOW-BY HEATER • Inspect the blow-by heater. (See BLOW-BY HEATER INSPECTION [SKYACTIV-D 2.2].) • Is the blow-by heater normal?	Yes	Go to the next step.
3		No	Replace the blow-by heater, then go to the next step. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
4	INSPECT FOR MALFUNCTION DUE TO DEVIATED VALVE TIMING • Inspect the valve timing (timing chain installation condition). (See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 2.2].) • Is the valve timing normal?	Yes	Go to the next step.
4		No	Adjust the valve timing to the correct timing, then go to Step 6.
5	INSPECT INSTRUMENT CLUSTER • Inspect the instrument cluster. (See INSTRUMENT CLUSTER INSPECTION.) • Is the instrument cluster normal?	Yes	Go to the next step.
5		No	Replace the instrument cluster, then go to the next step. (See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
6	Verify the test results. • If normal, return to the diagnostic index to service any additional symptoms. (See SYMPTOM DIAGNOSTIC INDEX [SKYACTIV-D 2.2].) • If a malfunction remains, inspect the related Service Information and perform the repair or diagnosis. ― If the vehicle is repaired, troubleshooting is completed. ― If the vehicle is not repaired or additional diagnostic information is not available, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)