DTC P050A:00 [MZI-3.7 (PCM CONNECTOR (3 TYPES))]


id0102e4301800

DTC P050A:00

Cold start idle air control system performance

DETECTION CONDITION
•  The monitor compares the actual measured engine speed to the engine speed requested by the powertrain control module (PCM). When the difference between desired and actual engine speed exceeds the calibrated threshold, the DTC sets.
POSSIBLE CAUSE
•  Intake air restriction
•  Exhaust restriction
•  Mechanical concern with engine
•  Damaged or sludged electronic throttle body (ETB)
•  Vacuum leakage
•  PCM malfunction

Diagnostic procedure

STEP

INSPECTION

ACTION

1
VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
•  Has FREEZE FRAME DATA been recorded?
Yes
Go to the next step.
No
Record FREEZE FRAME DATA on the repair order, then go to the next step.
2
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY RELATED PENDING CODE OR STORED DTCs
•  Turn the ignition switch off, then to the ON position (engine off).
•  Verify related pending code or stored DTCs.
•  Are other DTCs present?
Yes
Go to the appropriate DTC troubleshooting.
No
Go to the next step.
4
INSPECT AIR CLEANER ELEMENT
•  Remove air cleaner element with the engine running.
•  Is the engine speed increased?
Yes
Replace the air cleaner element, then go to Step 10.
No
Go to the next step.
5
PERFORM VISUAL INSPECTION ON INTAKE AIR SYSTEM AND ALL VACUUM HOSES
•  Turn the ignition switch off.
•  Check the intake air system for leaks, obstructions, and damage.
•  Inspect the entire length of all the vacuum hoses for:
―  In correct connections
―  Damage or cracks
―  Damaged or cracked vacuum hose joint
―  Improperly seated engine oil dipstick, tube or oil fill cap
•  Is a concern present?
Yes
Repair if necessary.
Then go to Step 10.
No
Go to the next step.
6
VERIFY DRIVE-BY-WIRE CONTROL SYSTEM OPERATION
•  Perform the Drive-by-Wire Control System Inspection.
•  Is there any malfunction?
Yes
Repair or replace the malfunctioning part according to the inspection results, then go to Step 10.
No
Go to the next step.
7
INSPECT THROTTLE VALVE
•  Turn the ignition switch off.
•  Remove the throttle valve with connector connected.
•  Access the ETC_DSD PID using the M-MDS.
•  Move the throttle valve using the ETC_DSD PID simulation function.
•  Does the throttle valve move smoothly?
Yes
Go to the next step.
No
Clean or replace the throttle valve and retest, then go to Step 10.
8
INSPECT ENGINE COMPRESSION
•  Inspect the engine compression.
•  Is the engine compression normal?
Yes
Go to the next step.
No
Overhaul the engine, then go to Step 10.
9
INSPECT FOR RESTRICTION IN EXHAUST SYSTEM AND TWC
•  Is there any restriction?
Yes
Replace malfunctioning part, then go to the next step.
No
Go to the next step.
10
VERIFY TROUBLESHOOTING OF DTC P050A:00 HAS BEEN COMPLETED
•  Verify that all disconnected connectors are reconnected.
•  Clear the DTC from the PCM memory using the M-MDS.
Caution
•  While performing this step, always operate the vehicle in a safe and lawful manner.
•  When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID/DATA MONITOR AND RECORD capturing function and inspect later.
•  Drive the vehicle under the FREEZE FRAME DATA condition.
•  Retrieve the DTCs using the M-MDS.
•  Is the PENDING CODE for this DTC present?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the PCM.
Go to the next step.
No
Go to the next step.
11
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
No
Troubleshooting completed.