NO.6 CRANKS NORMALLY BUT WILL NOT START [ZY]

id0103c0801200

6

CRANKS NORMALLY BUT WILL NOT START
DESCRIPTION
•  The starter cranks the engine at normal speed but the engine will not run.
•  Refer to symptom troubleshooting "No.5 Engine stalls" if this symptom appears after the engine stall.
•  Fuel is in the tank.
•  The battery is in normal condition.
POSSIBLE CAUSE
•  No battery power supply to PCM
•  Air leakage from intake-air system
•  Open PCM ground or vehicle body ground
•  Improper operation of electronic throttle control system
•  EGR valve malfunction
•  No signal from CKP sensor due to sensor, related wire or incorrect installation
•  No signal from CMP sensor due to sensor, related wire or incorrect installation
•  Low engine compression
•  Engine overheating
•  Vacuum leakage
•  Erratic signal to ignition coil
•  Improper air/fuel mixture ratio control
•  Poor fuel quality
•  PCV valve malfunction
•  Restriction in intake-air system
•  Restriction in exhaust system
•  Disconnected electrical connector
•  Open or short circuit in fuel pump body and related wiring harness
•  Inadequate fuel pressure
•  Fuel pump mechanical malfunction
•  Fuel leakage from injector
•  Fuel injector is clogged.
•  Purge solenoid valve malfunction
•  Spark plug malfunction
•  Ignition coil malfunction
•  Improper variable valve timing control system operation
•  Improper valve timing
•  Immobilizer system and/or circuit malfunction (if equipped)
•  Immobilizer system operating properly. (Ignition key is not registered.)
•  Pressure regulator malfunction
Warning
The following troubleshooting flow chart contains the fuel system diagnosis and repair procedures. Read the following warnings before performing the fuel system services:
•  Fuel vapor is hazardous. It can easily ignite, causing serious injury and damage. Always keep sparks and flames away from fuel.
•  Fuel line spills and leakage are dangerous. Fuel can ignite and cause serious injuries or death and damage. Fuel can also irritate skin and eyes. To prevent this, always complete the "BEFORE SERVICE PRECAUTION" and "AFTER SERVICE PRECAUTION" described in this manual.
Caution
•  If there is foreign material on the connecting area of the quick release connector, it might damage the connector or fuel pipe. To prevent this, disconnect the connector and clean the connecting area before connecting.

Diagnostic procedure

STEP

INSPECTION

RESULTS

ACTION
1
Note
•  Following test should be performed for vehicles with immobilizer system. Go to Step 10 for vehicles without immobilizer system.
Connect the WDS or equivalent to the DLC-2.
Do any of following conditions appear?
•  The engine is not completely started.
•  DTC P1681 is displayed.
Yes
Both conditions appear:
Go to Step 3.
No
Either or other condition appears:
Go to the next step.
2
Does the engine stall after approx. 2 s since the engine is started?
Yes
Go to the next step.
No
The immobilizer system is normal.
Go to Step 10.
3
Is the coil connector securely connected to the coil?
Yes
Go to the next step.
No
Connect the coil connector securely.
Return to Step 2.
4
Does the security light illuminate?
Yes
Go to the next step.
No
Inspect wiring harness between PCM terminal 1S and instrument cluster terminal 1G
•  If wiring harness is normal, inspect instrument cluster.
(See INSTRUMENT CLUSTER INSPECTION.)
5
Connect the WDS equivalent to the DLC-2 and retrieve DTC.
Are any of following DTCs displayed?
DTC
B1213, B1342, B1600, B1601, B1602, B1681, B2103, B2141
Yes
Go to the appropriate DTC inspection.
(See DTC TABLE [ZY].)
No
Go to the next step.
6
Is there continuity between PCM ground terminals 2BA, 2BH, 2BD, 2BB and ground?
Yes
Go to the next step.
No
Repair or replace suspected wiring harness and connector.
7
Turn the ignition switch to the ON position.
Measure voltage between PCM ground terminals 2BA, 2BH, 2BD, 2BB and coil terminal C.
Is the voltage 1.0 V or less?
Yes
Go to the next step.
No
Repair or replace the suspected wiring harness and connector.
8
Turn the ignition switch to the ON position.
Access VPWR PID.
Is VPWR PID normal?
Specification
Battery voltage
Yes
Go to the next step.
No
Repair or replace wiring harness.
9
Disconnect the coil connector.
Turn the ignition switch to the ON position.
Is there battery voltage at the coil connector terminal D (wiring harness-side)?
Yes
Inspect open or short circuit for following:
•  Between coil terminal A and PCM terminal 1AA
•  Between coil terminal B and PCM terminal 1W
No
Repair or replace wiring harness between the coil terminal D and the fuse panel.
10
Verify the following:
•  Vacuum connection
•  External fuel shut off or accessory (such as kill switch, alarm etc.)
•  Fuel quality: proper octane, contamination, winter/summer blend
•  No air leakage from intake-air system
•  Intake-air system restriction (such as air cleaner element, fresh air dust)
•  Proper sealing of the intake manifold and components attached to intake manifold: EGR valve
•  Ignition wiring
•  Electrical connections
•  Fuses
•  Smooth operation of throttle valve
Are all items normal?
Yes
Go to the next step.
No
Service if necessary.
Repeat Step 10.
11
Connect the WDS or equivalent to the DLC-2.
Retrieve any continuous memory and KOEO DTCs using WDS or equivalent.
Are there any DTCs displayed?
Yes
DTC is displayed:
Go to the appropriate DTC inspection.
(See DTC TABLE [ZY].)
Communication error message is displayed:
Inspect for following:
•  Open circuit in wiring harness between main relay and PCM terminal 1BF or 1BG (ATX)
•  Open circuit in wiring harness between main relay terminal E and PCM terminal 1AJ.
•  Main relay is stuck open.
•  Open or poor ground circuit (PCM terminal 2BA, 2BH, 2BD or 2BB)
•  Poor connection of vehicle body ground
No
No DTC is displayed:
Go to the next step.
12
Connect the WDS or equivalent to DLC-2.
Access the APP PID.
Crank the engine with accelerator pedal released.
Is APP PID indicating that the accelerator pedal is in the released position?
Yes
Go to the next step.
No
Inspect the following:
•  APP sensor
•  Wiring harness and connector for following:
―  PCM terminal 1F and APP sensor terminal A
―  PCM terminal 1C and APP sensor terminal B
―  PCM terminal 1AD and APP sensor terminal C
―  PCM terminal 1E and APP sensor terminal D
―  PCM terminal 1B and APP sensor terminal E
PCM terminal 1Z and APP sensor terminal F
13
Connect the WDS or equivalent to DLC-2.
Access the TP PID.
Crank the engine with accelerator pedal released.
Is TP PID indicating that the accelerator pedal is in the closed throttle position?
Yes
Go to the next step.
No
Inspect the following:
•  TP sensor
•  Wiring harness and connector for following:
―  PCM terminal 2AW and TP sensor terminal C
―  PCM terminal 2AT and TP sensor terminal D
―  PCM terminal 2AS and TP sensor terminal E
―  PCM terminal 2AX and TP sensor terminal F
14
Does engine start with the throttle valve closed?
Yes
Go to Step 27.
No
Go to the next step.
15
Does the engine start and run smoothly at part throttle?
Yes
Perform electronic throttle control inspection.
(See ENGINE CONTROL SYSTEM OPERATION INSPECTION [ZY].)
No
Go to the next step.
16
Connect WDS or equivalent to DLC-2.
Access RPM PID.
Is RPM PID indicating the engine speed when cranking engine?
Yes
Go to the next step.
No
Inspect for the following:
•  Open or short circuit in CKP sensor
•  Open or short circuit between CKP sensor terminal A and PCM terminal 2I
•  Open or short circuit between CKP sensor terminal B and PCM terminal 2Y
•  Open or short circuit between CKP sensor terminal C and body ground
If the CKP sensor and wiring harness are normal, go to the next step.
17
Visually inspect the CKP sensor and teeth of the crankshaft pulley.
Are the CKP sensor and teeth of the crankshaft pulley normal?
Yes
Go to the next step.
No
Replace the malfunctioning crankshaft pulley.
18
Measure the gap between the CKP sensor and teeth of the crankshaft pulley.
Specification
0.5—1.5 mm {0.02—0.05 in}
Is the gap within specification?
Yes
Go to the next step.
No
Replace the crankshaft pulley.
19
Inspect the ignition coil related wiring harness condition (intermittent open or short circuit) for all cylinders.
Are wiring harness conditions normal?
Yes
Go to the next step.
No
Repair the wiring harnesses.
20
Perform the spark test.
(See ENGINE CONTROL SYSTEM OPERATION INSPECTION [ZY].)
Is strong blue spark visible at each cylinder?
Yes
Go to the next step.
No
Repair or replace the malfunctioning part according to spark test result.
21
Inspect the spark plug conditions.
Is the spark plug wet, covered with carbon or grayish white?
Yes
Spark plug is wet or covered with carbon:
Inspect for fuel leakage from the fuel injector.
Spark plug is grayish white:
Inspect for clogged the fuel injector.
No
Install the spark plugs on original cylinders.
Go to the next step.
22
Remove and shake the PCV valve.
Does the PCV valve rattle?
Yes
Go to the next step.
No
Replace the PCV valve.
23
Visually inspect the exhaust system part.
Is there any deformed exhaust system part?
Yes
Replace the suspected part.
No
Go to the next step.
24
Install fuel pressure gauge between fuel pipe and the fuel distributor.
Connect the WDS or equivalent to the DLC-2.
Turn ON and/or OFF using FP PID in output state control of datalogger function.
Is fuel line pressure correct when FP PID is turned ON/OFF five times?
(See FUEL LINE PRESSURE INSPECTION [ZY].)
Yes
Go to the next step.
No
Zero or low:
Inspect the fuel pump relay and the fuel pump related circuit.
(See FUEL PUMP UNIT INSPECTION [ZY].)
Inspect the main fuel line for clogging.
•  If there is no malfunction, replace fuel pump unit.
High:
Replace the fuel pump unit.
(See FUEL PUMP UNIT REMOVAL/INSTALLATION [ZY].)
25
Visually inspect for fuel leakage at the fuel injector O-ring and fuel line.
Service if necessary.
Turn OFF from ON using FP PID in output state control of datalogger function.
Is fuel line pressure held after FP PID is turned OFF?
(See FUEL LINE PRESSURE INSPECTION [ZY].)
Yes
Go to the next step.
No
Inspect the pressure regulator diaphragm condition.
•  If condition is normal, inspect the fuel injector.
•  If condition is not normal, replace the fuel pump unit.
26
Disconnect the vacuum hose between the purge solenoid valve and the intake manifold from the purge solenoid valve side.
Plug the opening end of vacuum hose.
Attempt to start engine.
Is starting condition improved?
Yes
Inspect if the purge solenoid valve is stuck open mechanically.
Inspect the evaporative emission control system.
No
Go to the next step.
27
Is air leakage felt or heard at intake-air system components while the racing the engine to higher speed?
Yes
Repair or replace the malfunctioning part.
No
Go to the next step.
28
Inspect engine condition while tapping the EGR valve housing.
Does engine condition improve?
Yes
Replace the EGR valve.
No
Go to the next step.
29
Inspect variable valve timing control system operation.
(See ENGINE CONTROL SYSTEM OPERATION INSPECTION [ZY].)
Does variable valve timing control work properly?
Yes
Go to the next step.
No
Repair or replace the malfunctioning part.
30
Is engine compression correct?
(See COMPRESSION INSPECTION [ZY].)
Yes
Remove the EGR valve and visually inspect for mechanically stuck EGR valve.
•  If normal, inspect valve timing.
No
Inspect for cause.
31
Verify test results.
•  If normal, return to diagnostic index to service any additional symptoms.
•  If malfunction remains, inspect related Service information perform repair or diagnosis.
―  If vehicle repaired, troubleshooting completed.
―  If vehicle not repaired or additional diagnostic information not available, replace the PCM.