DTC TABLE [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)]

id0902e3347100

Note

•  The security light flashes or illuminates under the following conditions when the ignition switch is turned to the LOCK or ACC position.

•  If there is any malfunction:

―  DTC 16 or below: Flashes for approx. 1 min and the DTC flash pattern indicated in the table below repeats 10 times.

―  DTC 21 or higher: Illuminates for approx. 1 min and the DTC flash pattern indicated in the table below repeats 10 times.

―  If more than one DTC is detected, only the DTC with the lowest number is displayed.

•  If there is no malfunction:

―  The security light illuminates for approx. 3 s and then turns off.

DTC					Description	Reference
Security light flashing pattern		Keyless warning light	M-MDS display*
			Keyless control module	PCM
11		Illuminated	B10D9:87	P1260:00	•  No detected communication with coil antenna.	(See SECURITY LIGHT: 11, DTC: B10D9:87/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)].)
12		Illuminated	B10D5:13	P1260:00	•  Coil antenna malfunction •  PCM determines a malfunction in coil antenna even though it is normal	(See SECURITY LIGHT: 12, DTC: B10D5:13/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)].)
13		Not illuminated	B10D7:05	P1260:00	•  Key ID number programing error	(See SECURITY LIGHT: 13, DTC: B10D7:05/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)].)
		Not illuminated	B10D7:94	P1260:00	•  Key ID number data cannot be read	(See SECURITY LIGHT: 13, DTC: B10D7:94/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)].)
14		Not illuminated	B10D7:81	P1260:00	•  Keyless control module cannot read key ID number data normally	(See SECURITY LIGHT: 14, DTC: B10D7:81/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)].)
15		Not illuminated	B10D7:51	P1260:00	•  Keyless control module has detected unprogrammed key ID number	(See SECURITY LIGHT: 15, DTC: B10D7:51/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)].)
16		Not illuminated	U0100:87	P1260:00	•  Communication error between keyless control module and PCM (no response)	(See SECURITY LIGHT: 16, DTC: U0100:87/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)].)
21		Illuminated	B10D8:00	P1260:00	•  Only one key has been programmed	(See SECURITY LIGHT: 21, DTC: B10D8:00/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)].)
22		Not illuminated	B10DA:51	P1260:00	•  Communication error between keyless control module and PCM (data transfer error)	(See SECURITY LIGHT: 22, DTC: B10DA:51/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)].)
23		Not illuminated	B10DA:62	P1260:00	•  Key ID number data between keyless control module and PCM are different	(See SECURITY LIGHT: 23, DTC: B10DA:62/P1260:00 [IMMOBILIZER SYSTEM (ADVANCED KEYLESS AND START SYSTEM)].)
Not illuminated		Illuminated	U0001:88	U0073:00	•  CAN system communication error (HS-CAN)	(See FOREWORD [MULTIPLEX COMMUNICATION SYSTEM (L.H.D.)].) (See FOREWORD [MULTIPLEX COMMUNICATION SYSTEM (R.H.D.)].)
		Illuminated	U0100:00	-	•  Communication error to PCM