WASHER MOTOR INSPECTION

id091900805100

Note
•  If the procedure is performed with washer fluid in the washer tank, the washer fluid may leak out. When performing the procedure, place a container under the washer tank to collect washer fluid, and perform the procedure.

VIN: Except 3MZ


4SD

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

2.  Remove the set plate. (See SET PLATE REMOVAL/INSTALLATION.)

3.  Remove the front bumper. (See FRONT BUMPER REMOVAL.) (See FRONT BUMPER INSTALLATION.)

4.  Disconnect the connector. (See WASHER MOTOR REMOVAL/INSTALLATION.)

5.  Disconnect the washer hose from the washer motor. (See WASHER MOTOR REMOVAL/INSTALLATION.)

6.  Apply battery voltage to washer motor terminal A, and connect terminal B to ground.

Warning
•  Water sprayed on the battery and ground could cause electrocution. When performing the washer motor inspection, prepare a container to collect washer fluid and be careful not to spray washer fluid.
am3uuw00011947

7.  Verify that washer fluid sprays from the washer motor.

am3uuw00011948

•  If washer fluid does not spray from the washer motor, replace the washer motor. (See WASHER MOTOR REMOVAL/INSTALLATION.)


5HB

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

2.  Remove the set plate. (See SET PLATE REMOVAL/INSTALLATION.)

3.  Remove the front bumper. (See FRONT BUMPER REMOVAL.) (See FRONT BUMPER INSTALLATION.)

4.  Disconnect the connector. (See WASHER MOTOR REMOVAL/INSTALLATION.)

5.  Disconnect the washer hose from the washer motor. (See WASHER MOTOR REMOVAL/INSTALLATION.)

6.  Apply battery voltage to washer motor terminal A, and connect terminal B to ground.

Warning
•  Water sprayed on the battery and ground could cause electrocution. When performing the washer motor inspection, prepare a container to collect washer fluid and be careful not to spray washer fluid.
am3uuw00010624

7.  Verify that washer fluid sprays from the front side of the washer motor.

am3uuw00010625

•  If washer fluid does not spray from the front side of the washer motor, replace the washer motor. (See WASHER MOTOR REMOVAL/INSTALLATION.)

8.  Apply battery positive voltage to washer motor terminal B, and connect terminal A to ground.

9.  Verify that washer fluid sprays from the rear side of the washer motor.

am3uuw00010626

•  If washer fluid does not spray from the rear side of the washer motor, replace the washer motor. (See WASHER MOTOR REMOVAL/INSTALLATION.)


VIN: 3MZ


4SD

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

2.  Remove the set plate. (See SET PLATE REMOVAL/INSTALLATION.)

3.  Remove the front bumper. (See FRONT BUMPER REMOVAL.) (See FRONT BUMPER INSTALLATION.)

4.  Disconnect the connector. (See WASHER MOTOR REMOVAL/INSTALLATION.)

5.  Disconnect the washer hose from the washer motor. (See WASHER MOTOR REMOVAL/INSTALLATION.)

6.  Apply battery voltage to washer motor terminal B, and connect terminal A to ground.

Warning
•  Water sprayed on the battery and ground could cause electrocution. When performing the washer motor inspection, prepare a container to collect washer fluid and be careful not to spray washer fluid.
am3zzw00020146

7.  Verify that washer fluid sprays from the washer motor.

am3zzw00020147

•  If washer fluid does not spray from the washer motor, replace the washer motor. (See WASHER MOTOR REMOVAL/INSTALLATION.)


5HB

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

2.  Remove the set plate. (See SET PLATE REMOVAL/INSTALLATION.)

3.  Remove the front bumper. (See FRONT BUMPER REMOVAL.) (See FRONT BUMPER INSTALLATION.)

4.  Disconnect the connector. (See WASHER MOTOR REMOVAL/INSTALLATION.)

5.  Disconnect the washer hose from the washer motor. (See WASHER MOTOR REMOVAL/INSTALLATION.)

6.  Apply battery voltage to washer motor terminal B, and connect terminal A to ground.

Warning
•  Water sprayed on the battery and ground could cause electrocution. When performing the washer motor inspection, prepare a container to collect washer fluid and be careful not to spray washer fluid.
am3zzw00020148

7.  Verify that washer fluid sprays from the front side of the washer motor.

am3zzw00020149

•  If washer fluid does not spray from the front side of the washer motor, replace the washer motor. (See WASHER MOTOR REMOVAL/INSTALLATION.)

8.  Apply battery positive voltage to washer motor terminal A, and connect terminal B to ground.

9.  Verify that washer fluid sprays from the rear side of the washer motor.

am3zzw00020150

•  If washer fluid does not spray from the rear side of the washer motor, replace the washer motor. (See WASHER MOTOR REMOVAL/INSTALLATION.)