STARTER REMOVAL/INSTALLATION [SKYACTIV-G 2.0]

id0119h7800200

Operation After Replacing Starter

Note

• If the number of times the starter can operate exceeds the limit, or there is any malfunction of the i-stop system-related parts, the i-stop warning light (amber) flashes.In addition, DTCs are stored simultaneously.

• To ensure reliability of the i-stop system, replace the starter with a new one if the number of times the starter can operate has exceeded the upper limit.

• When replacing the starter, perform the following procedure: When replacing the PCM simultaneously, perform the PCM configuration first. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 2.0].) (See PCM CONFIGURATION [SKYACTIV-G 2.0].)

Step

Action

1

Note

•  Perform the procedures from Step 1 to 5 within 2 min.

―  If the operation exceeds 2 min, switch the ignition off and repeat the procedures from Step 1.

Switch the ignition ON.

2

Apply the parking brake firmly.

3

Shift the selector lever to the N position.

4

Perform the following work with the brake pedal depressed.

1.  Depress and release the accelerator pedal 6 times.

2.  Verify that the i-stop indicator light (green) flashes.

•  If the light does not flash, switch the ignition off and repeat the procedure from Step 1.

3.  Depress and release the accelerator pedal 6 times.

4.  Verify that the i-stop indicator light (green) changes from flashing to illumination.

•  If the light does not change to illumination, switch the ignition off and repeat the procedure from Step 1.

5

Long-press the i-stop OFF switch.

Wait until the i-stop indicator light (green) turns off (for 5 s or more).

•  If the light does not turn off, switch the ignition off and repeat the procedure from Step 1.

6

Switch the ignition off.

7

Start the engine.

8

Verify that the i-stop warning light (amber) turns off.

•  If the light does not turn off, switch the ignition off and repeat the procedure from Step 1.

9

Switch the ignition off and disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0].)

10

Verifying battery condition initialization learning (i-stop learning). (See BATTERY CONDITION INITIALIZATION LEARNING (i-stop LEARNING) [SKYACTIV-G 2.0].)

Step	Action
1	Note • Perform the procedures from Step 1 to 5 within 2 min. ― If the operation exceeds 2 min, switch the ignition off and repeat the procedures from Step 1. Switch the ignition ON.
2	Apply the parking brake firmly.
3	Shift the selector lever to the N position.
4	Perform the following work with the brake pedal depressed. 1. Depress and release the accelerator pedal 6 times. 2. Verify that the i-stop indicator light (green) flashes. • If the light does not flash, switch the ignition off and repeat the procedure from Step 1. 3. Depress and release the accelerator pedal 6 times. 4. Verify that the i-stop indicator light (green) changes from flashing to illumination. • If the light does not change to illumination, switch the ignition off and repeat the procedure from Step 1.
5	Long-press the i-stop OFF switch. Wait until the i-stop indicator light (green) turns off (for 5 s or more). • If the light does not turn off, switch the ignition off and repeat the procedure from Step 1.
6	Switch the ignition off.
7	Start the engine.
8	Verify that the i-stop warning light (amber) turns off. • If the light does not turn off, switch the ignition off and repeat the procedure from Step 1.
9	Switch the ignition off and disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 2.0].)
10	Verifying battery condition initialization learning (i-stop learning). (See BATTERY CONDITION INITIALIZATION LEARNING (i-stop LEARNING) [SKYACTIV-G 2.0].)

Starter Removal/Installation

Warning

• Remove and install all parts when the engine is cold, otherwise they can cause severe burns or serious injury.

• When the battery cables are connected, touching the vehicle body with starter terminal B will generate sparks. This can cause personal injury, fire, and damage to the electrical components. Always disconnect the negative battery cable before performing the following operation.

1. Remove the battery cover. (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)

2. Disconnect the negative battery cable. (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0].)

3. Remove the aerodynamic under cover No.2. (See AERODYNAMIC UNDER COVER NO.2 REMOVAL/INSTALLATION.)

4. Remove in the order indicated in the table.

5. Install in the reverse order of removal.

am3zzw00012627

1

Terminal B cable

2

Terminal S connector

3

Starter

(See Operation After Replacing Starter.)

(See Starter installation note.)

Starter installation note

Caution

• Do not overlap the starter with the end plate (area A shown in figure) when installing. If the starter is not correctly installed, the nut installed to the drive plate may contact the end plate causing abnormal noise.

ac5ccw00000247

1	Terminal B cable
2	Terminal S connector
3	Starter (See Operation After Replacing Starter.) (See Starter installation note.)