NO.17 EXCESSIVE SHIFT SHOCK FROM N TO D OR N TO R POSITION/RANGE [FS5A-EL]

id050308802200

17

Excessive shift shock from N to D or N to R position/range

DESCRIPTION

•  Strong shock is felt when shifting from N to D or N to R position/range at idle.

POSSIBLE CAUSE

•  Shift shock may worsen when the fail-safe is operating. If no DTC is output, the shift shock may worsen due to poor operation of the control valve body or sticking of the clutch.

1.  Clutch burnt (N→D: Forward clutch, N→R: Reverse clutch or low and reverse brake)

•  Line pressure low, high

•  APP sensor malfunction

•  Input/turbine speed sensor malfunction

•  VSS malfunction

•  Shift solenoid A malfunction

•  Shift solenoid B malfunction

•  Shift solenoid C malfunction

•  Shift solenoid D malfunction

•  Pressure control solenoid A malfunction

•  Control valve body malfunction

•  Sensor GND malfunction

•  Body GND malfunction

2.  Poor hydraulic operation (Malfunction in range change)

•  Forward accumulator malfunction

•  Servo apply accumulator malfunction

•  Oil pressure switch malfunction

3.  Idle speed high

4.  Poor tightening torque of engine mount, exhaust mount

5.  Poor operation of mechanical pressure

•  Selector lever position disparity

Note

•  Before following the troubleshooting steps, make sure that the Automatic Transaxle On-Board Diagnostic and Automatic Transaxle Basic Inspection are conducted. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FS5A-EL].) (See BASIC INSPECTION [FS5A-EL].)

Diagnostic procedure

STEP	INSPECTION		ACTION
1	Does the shift shock occur only when the engine is cold?	Yes	Go to the next step.
1	Does the shift shock occur only when the engine is cold?	No	Go to Step 3.
2	Disconnect the TCM connector. Measure the resistance between ground terminal at the TCM connector and body ground. Is the resistance less than 5.0 ohms?	Yes	Inspect the following PCM and TCM PID values using the M-MDS: (See ON-BOARD DIAGNOSTIC TEST [MZR 2.0, MZR 2.5].) (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FS5A-EL].) PCM PID: • APP TCM PIDs: • THOP • TFT • TFTV Repair or replace any malfunctioning parts. (See PCM INSPECTION [MZR 2.0, MZR 2.5].)
2		No	Repair or replace the wiring harness for a possible open circuit.
3	Perform the stall test. (See MECHANICAL SYSTEM TEST [FS5A-EL].) Is the stall speed normal?	Yes	Go to the next step.
3		No	Go to Step 5.
4	Inspect the TR PID value using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FS5A-EL].) Is the PID value normal?	Yes	Overhaul the control valve body and repair or replace any malfunctioning parts. (See ATX workshop manual [FS5A-EL].) If any problem remains: • Overhaul the transaxle and repair or replace any malfunctioning parts. (See ATX workshop manual [FS5A-EL].)
4		No	Repair or replace any malfunctioning parts.
5	Inspect the THOP PID value using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FS5A-EL].) Is the PID value normal?	Yes	Go to the next step.
5		No	Repair or replace any malfunctioning parts.
6	Disconnect the TCM connector. Measure the resistance between ground terminal at the TCM connector and body ground. Is the resistance less than 5.0 ohms?	Yes	Go to the next step.
6		No	Repair or replace the wiring harness for a possible open circuit.
7	Inspect the LPS PID value using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FS5A-EL].) Is the PID value normal?	Yes	Overhaul the control valve body and repair or replace any malfunctioning parts. (See ATX workshop manual [FS5A-EL].) If any problem remains: • Overhaul the transaxle and repair or replace any malfunctioning parts. (See ATX workshop manual [FS5A-EL].)
7		No	Repair or replace any malfunctioning parts.
8	• Verify the test results. ― If normal, return to the diagnostic index to service any additional symptoms. ― If the malfunction remains, inspect the related Service Information and perform repair or diagnosis. • If the vehicle is repaired, troubleshooting is completed. • If the vehicle is not repaired or additional diagnostic information is not available, replace the TCM. (See TCM REMOVAL/INSTALLATION [FS5A-EL].)