CLUTCH DISC INSPECTION [A26M-R (MZR 2.3 DISI Turbo)]

id0510008009c4

Caution

• Secure the steering wheel using tape or a cable to prevent the steering shaft from rotating after disconnecting the steering shaft. If the steering wheel rotates after the steering shaft and the steering gear and linkage are disconnected, the internal parts of the clock spring could be damaged.

1. Remove the battery cover. (See BATTERY RECHARGING [MZR 2.3 DISI Turbo].)

2. Disconnect the negative battery cable. (See BATTERY RECHARGING [MZR 2.3 DISI Turbo].)

3. Drain the engine coolant. (See ENGINE COOLANT REPLACEMENT [MZR 2.3 DISI Turbo].)

4. Remove the PCM cover No.1. (See PCM REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].)

5. Disconnect the PCM connector. (See PCM REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].)

6. Remove the following parts:

(1) Battery tray and PCM component (See BATTERY RECHARGING [MZR 2.3 DISI Turbo].)

(2) Air cleaner component (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].)

(3) Charge air cooler cover (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].)

(4) Charge air cooler (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].)

(5) Front tires (See GENERAL PROCEDURES (SUSPENSION).)

(6) Splash shield (See SPLASH SHIELD REMOVAL/INSTALLATION.)

(7) Aerodynamic under cover No.2 (See AERODYNAMIC UNDER COVER NO.2 REMOVAL/INSTALLATION.)

7. Remove the starter. (See STARTER REMOVAL/INSTALLATION [MZR 2.3 DISI Turbo].)

8. Remove the front auto leveling sensor. (See AUTO LEVELING SENSOR REMOVAL/INSTALLATION.)

9. Drain the transaxle oil into a suitable container. (See TRANSAXLE OIL REPLACEMENT [A26M-R].)

10. Remove the manual transaxle. (See MANUAL TRANSAXLE REMOVAL/INSTALLATION [A26M-R (MZR 2.3 DISI Turbo)].)

11. Remove the clutch cover. (See CLUTCH UNIT REMOVAL/INSTALLATION [A26M-R (MZR 2.3 DISI Turbo)].)

12. Remove the clutch disk. (See CLUTCH UNIT REMOVAL/INSTALLATION [A26M-R (MZR 2.3 DISI Turbo)].)

13. Using vernier calipers, measure the thickness of the lining at a rivet head on both sides.

am3zzw00008405

• If it less than the minimum specification, replace the clutch disc. (See CLUTCH UNIT REMOVAL/INSTALLATION [A26M-R (MZR 2.3 DISI Turbo)].)

Minimum clutch disc thickness

0.3 mm {0.01 in}

14. Measure the clutch disc runout using a dial gauge.

am6uuw00001269

• If it exceeds the maximum specification, replace the clutch disc. (See CLUTCH UNIT REMOVAL/INSTALLATION [A26M-R (MZR 2.3 DISI Turbo)].)

Maximum clutch disc runout

0.7 mm {0.03 in}

15. Install in the reverse order of removal.

16. Add the specified amount of specified transaxle oil. (See TRANSAXLE OIL REPLACEMENT [A26M-R].)

17. Warm up the engine and transaxle, inspect for oil leakage, and inspect the transaxle operation.

Warning

• Improperly jacking a transaxle is dangerous. It can slip off the jack and may cause serious injury.

Note

• If the transaxle is overhauled and installed to the vehicle, perform the 'INSPECTION AFTER TRANSAXLE OVERHAUL' and verify that there is no abnormality. (See INSPECTION AFTER TRANSAXLE INSTALLATION [A26M-R].)