DTC B1079:13 [BCM]

id0902f5415000

DESCRIPTION

Bonnet latch switch circuit malfunction
DETECTION CONDITION
•  Open circuit in the bonnet latch switch circuit with the bonnet closed (bonnet latch switch on).
POSSIBLE CAUSE
•  Bonnet latch switch connector or terminals malfunction
•  Open circuit in wiring harness between bonnet latch switch terminal B and body ground
•  Bonnet latch switch malfunction
•  BCM connector or terminals malfunction
•  Open circuit in wiring harness between bonnet latch switch terminal A and BCM terminal 1J
•  BCM malfunction

Diagnostic Procedure

STEP

INSPECTION

ACTION
1
CONFIRM BCM DTC
•  Clear the DTC using the M-MDS.
•  Perform the BCM DTC inspection using the M-MDS.
•  Is the same DTC present?
Yes
Go to the next step.
No
Go to Step 9.
2
INSPECT BONNET LATCH SWITCH CONNECTOR AND TERMINALS
•  Switch the ignition to off.
•  Disconnect the negative battery cable.
•  Disconnect the bonnet latch switch connector.
•  Inspect the connector and terminals (corrosion, damage, pin disconnection).
•  Is there any malfunction?
Yes
Repair or replace the connector or terminals, then go to Step 8.
No
Go to the next step.
3
VERIFY MALFUNCTIONING LOCATION
•  Verify that the bonnet latch switch connector is disconnected.
•  Reconnect the negative battery cable.
•  Measure the voltage at the bonnet latch switch terminal A (wiring harness-side).
•  Is there any voltage?
Yes
Go to the next step.
No
Go to Step 6.
4
INSPECT BONNET LATCH SWITCH GROUND CIRCUIT FOR OPEN CIRCUIT
•  Verify that the bonnet latch switch connector is disconnected.
•  Disconnect the negative battery cable.
•  Inspect for continuity between bonnet latch switch terminal B (wiring harness-side) and body ground.
•  Is there continuity?
Yes
Go to the next step.
No
Repair or replace the wiring harness for a possible open circuit, then go to Step 8.
5
INSPECT BONNET LATCH SWITCH
•  Inspect the bonnet latch switch.
•  Is there any malfunction?
Yes
Replace the bonnet latch switch, then go to Step 8.
(See BONNET LATCH AND RELEASE LEVER REMOVAL/INSTALLATION.)
No
Go to Step 8.
6
INSPECT BCM CONNECTOR AND TERMINALS
•  Disconnect the negative battery cable.
•  Disconnect the BCM connector.
•  Inspect the connector and terminals (corrosion, damage, pin disconnection).
•  Is there any malfunction?
Yes
Repair or replace the connector or terminals, then go to Step 8.
No
Go to the next step.
7
INSPECT BONNET LATCH SWITCH CIRCUIT FOR OPEN CIRCUIT
•  Verify that the bonnet latch switch and BCM connectors are disconnected.
•  Reconnect the BCM connector.
•  Reconnect the negative battery cable.
•  Measure the voltage at the BCM terminal 1J (wiring harness-side).
•  Is there any voltage?
Yes
Repair or replace the wiring harness for a possible open circuit, then go to the next step.
No
BCM internal malfunction can be considered the cause.
•  Go to the next step.
8
VERIFY TROUBLESHOOTING COMPLETED
•  Make sure to reconnect all disconnected connectors.
•  Reconnect the negative battery cable.
•  Clear the DTC using the M-MDS.
•  Perform the BCM DTC inspection using the M-MDS.
•  Is the same DTC present?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the BCM.
Go to the next step.
No
Go to the next step.
9
VERIFY THAT NO OTHER DTCs ARE PRESENT
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [BCM].)
No
DTC troubleshooting completed.