INTERIOR LIGHT REMOVAL/INSTALLATION
id091800801500
4SD
1. Disconnect the negative battery cable.
2. Partially peel back the seaming welt.
3. Remove the rain sensor cover. (Vehicles with auto light / wiper system) (See RAIN SENSOR REMOVAL/INSTALLATION)
4. Disconnect the rain sensor connector. (Vehicles auto light / wiper system)
5. Remove the following parts:
- (1) Sunroof seaming welt (vehicles with sunroof only)
- (2) A-pillar trims (See A-PILLAR TRIM REMOVAL/INSTALLATION.)
- (3) Upper anchor of the front seat belt (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
- (4) Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
- (5) Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION.)
- (6) B-pillar lower trims (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
- (7) B-pillar upper trims (See B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
- (8) Rear seat cushion (See REAR SEAT CUSHION REMOVAL/INSTALLATION [4SD].)
- (9) Rear side seat back (See REAR SIDE SEAT BACK REMOVAL/INSTALLATION.)
- (10) Tire house trims (See TIRE HOUSE TRIM REMOVAL/INSTALLATION.)
- (11) C-pillar trims (See C-PILLAR TRIM REMOVAL/INSTALLATION.)
6. Disconnect the auto-dimming mirror connector. (vehicles with auto-dimming mirror only)
7. Remove the sunvisors. (See SUNVISOR REMOVAL/INSTALLATION)
8. Remove the front map light. (See MAP LIGHT REMOVAL/INSTALLATION)
9. Remove the assist handle. (See ASSIST HANDLE REMOVAL/INSTALLATION)
10. Remove the headliner. (See HEADLINER REMOVAL/INSTALLATION.)
11. Detach the tab and remove the bulb housing.
-
Note
-
• The valve housing and the wiring harness have been integrated and attached to the headliner. When replacing the valve housing, remove the wiring harness which passes under the urethane by cutting the urethane.
12. Pull in the direction of the arrows and detach the tabs.
13. Remove the interior light.
14. Install in the reverse order of removal.
-
Note
-
• After installing the wiring harness, reinforce the urethane that was cut when removing the valve housing with vinyl tape.
5HB
1. Disconnect the negative battery cable.
2. Partially peel back the seaming welt.
3. Remove the rain sensor cover. (Vehicles with auto light / wiper system) (See RAIN SENSOR REMOVAL/INSTALLATION)
4. Disconnect the rain sensor connector. (Vehicles auto light / wiper system)
5. Remove the following parts:
- (1) Sunroof seaming welt (vehicles with sunroof only)
- (2) A-pillar trims (See A-PILLAR TRIM REMOVAL/INSTALLATION.)
- (3) Upper anchor of the front seat belt (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
- (4) Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
- (5) Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION.)
- (6) B-pillar lower trims (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
- (7) B-pillar upper trims (See B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
- (8) Tire house trims (See TIRE HOUSE TRIM REMOVAL/INSTALLATION.)
- (9) Trunk side upper trims (See TRUNK SIDE UPPER TRIM REMOVAL/INSTALLATION.)
- (10) Rear seat (See REAR SEAT REMOVAL/INSTALLATION [5HB/WAGON].)
- (11) Lower anchor of the rear seat belt installation bolts (LH) (See REAR SEAT BELT REMOVAL/INSTALLATION [5HB, WGN].)
- (12) C-pillar trims (See C-PILLAR TRIM REMOVAL/INSTALLATION.)
6. Disconnect the auto-dimming mirror connector. (Vehicles with auto-dimming mirror only)
7. Remove the sunvisors. (See SUNVISOR REMOVAL/INSTALLATION)
8. Remove the front map light. (See MAP LIGHT REMOVAL/INSTALLATION)
9. Remove the assist handle. (See ASSIST HANDLE REMOVAL/INSTALLATION)
10. Remove the headliner. (See HEADLINER REMOVAL/INSTALLATION.)
11. Detach the tab and remove the bulb housing.
-
Note
-
• The valve housing and the wiring harness have been integrated and attached to the headliner. When replacing the valve housing, remove the wiring harness which passes under the urethane by cutting the urethane.
12. Pull in the direction of the arrows and detach the tabs.
13. Remove the interior light.
14. Install in the reverse order of removal.
-
Note
-
• After installing the wiring harness, reinforce the urethane that was cut when removing the valve housing with vinyl tape.
WGN
1. Disconnect the negative battery cable.
2. Partially peel back the seaming welt.
3. Remove the rain sensor cover. (Vehicles with auto light / wiper system) (See RAIN SENSOR REMOVAL/INSTALLATION)
4. Disconnect the rain sensor connector. (Vehicles auto light / wiper system)
5. Remove the following parts:
- (1) Sunroof seaming welt (vehicles with sunroof only)
- (2) A-pillar trims (See A-PILLAR TRIM REMOVAL/INSTALLATION.)
- (3) Upper anchor of the front seat belt (See FRONT SEAT BELT REMOVAL/INSTALLATION.)
- (4) Front scuff plate (See FRONT SCUFF PLATE REMOVAL/INSTALLATION.)
- (5) Rear scuff plate (See REAR SCUFF PLATE REMOVAL/INSTALLATION.)
- (6) B-pillar lower trims (See B-PILLAR LOWER TRIM REMOVAL/INSTALLATION.)
- (7) B-pillar upper trims (See B-PILLAR UPPER TRIM REMOVAL/INSTALLATION.)
- (8) Tire house trims (See TIRE HOUSE TRIM REMOVAL/INSTALLATION.)
- (9) Trunk side upper trims (See TRUNK SIDE UPPER TRIM REMOVAL/INSTALLATION.)
- (10) Rear seat (See REAR SEAT REMOVAL/INSTALLATION [5HB/WAGON].)
- (11) Lower anchor of the rear seat belt installation bolts (LH) (See REAR SEAT BELT REMOVAL/INSTALLATION [5HB, WGN].)
- (12) C-pillar trims (See C-PILLAR TRIM REMOVAL/INSTALLATION.)
- (13) D-pillar trims (See D-PILLAR TRIM REMOVAL/INSTALLATION.)
6. Disconnect the auto-dimming mirror connector. (Vehicles with auto-dimming mirror only)
7. Remove the sunvisors. (See SUNVISOR REMOVAL/INSTALLATION)
8. Remove the front map light. (See MAP LIGHT REMOVAL/INSTALLATION)
9. Remove the assist handles. (See ASSIST HANDLE REMOVAL/INSTALLATION)
10. Remove the headliner. (See HEADLINER REMOVAL/INSTALLATION.)
11. Detach the tab and remove the bulb housing.
-
Note
-
• The valve housing and the wiring harness have been integrated and attached to the headliner. When replacing the valve housing, remove the wiring harness which passes under the urethane by cutting the urethane.
12. Pull in the direction of the arrows and detach the tabs.
13. Remove the interior light.
14. Install in the reverse order of removal.
-
Note
-
• After installing the wiring harness, reinforce the urethane that was cut when removing the valve housing with vinyl tape.
