DTC U3003:17 [AUDIO AMPLIFIER]

id0902f8848800

Description

Audio amplifier high power supply voltage input

Detection condition

Larger value than audio amplifier power supply circuit voltage of 16.0 ± 0.8 V or more is detected for 5 s or more with ignition switched ACC or ON (engine off or on)

Fail-safe

Not applicable

Possible cause

•  DTCs are stored in the PCM.

•  Battery malfunction

•  Generator malfunction

•  Audio amplifier malfunction

System wiring diagram

Not applicable

Description	Audio amplifier high power supply voltage input
Detection condition	Larger value than audio amplifier power supply circuit voltage of 16.0 ± 0.8 V or more is detected for 5 s or more with ignition switched ACC or ON (engine off or on)
Fail-safe	Not applicable
Possible cause	• DTCs are stored in the PCM. • Battery malfunction • Generator malfunction • Audio amplifier malfunction
System wiring diagram	Not applicable

Diagnostic Procedure

Step	Inspection		Action
1	VERIFY PCM DTCs • Perform the DTC inspection for the PCM using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-D 2.2)].) (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5T)].) (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION))].) (See ON-BOARD DIAGNOSTIC TEST [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION))].) • Is the DTC displayed?	Yes	Repair the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [PCM (SKYACTIV-D 2.2)].) (See DTC TABLE [PCM (SKYACTIV-G 2.5T)].) (See DTC TABLE [PCM (SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION))].) (See DTC TABLE [PCM (SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION))].)
1		No	Go to the next step.
2	INSPECT BATTERY • Inspect the battery. (See BATTERY INSPECTION.) • Is there any malfunctioning part?	Yes	Replace the battery, then go to Step 4. (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-D 2.2].) (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.5T].) (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION)].) (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)].)
2		No	Go to the next step.
3	INSPECT GENERATOR • Inspect the generator. (See GENERATOR INSPECTION [WITHOUT i-ELOOP (SKYACTIV-D 2.2)].) (See GENERATOR INSPECTION [SKYACTIV-G 2.5T].) (See GENERATOR DISASSEMBLY/ASSEMBLY [WITHOUT i-ELOOP (SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION))].) (See GENERATOR INSPECTION [WITH i-ELOOP (SKYACTIV-D 2.2)].) (See GENERATOR INSPECTION [WITH i-ELOOP (SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION))].) • Is there any malfunctioning part?	Yes	Replace the generator, then go to the next step. (See GENERATOR REMOVAL/INSTALLATION [WITHOUT i-ELOOP (SKYACTIV-D 2.2)].) (See GENERATOR REMOVAL/INSTALLATION [SKYACTIV-G 2.5T].) (See GENERATOR REMOVAL/INSTALLATION [WITHOUT i-ELOOP (SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION))].) (See GENERATOR REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-D 2.2)].) (See GENERATOR REMOVAL/INSTALLATION [SKYACTIV-G 2.5 (WITH CYLINDER DEACTIVATION)].) (See GENERATOR REMOVAL/INSTALLATION [WITH i-ELOOP (SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION))].)
3		No	Go to the next step.
4	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Clear the audio amplifier DTCs. (See CLEARING DTC [AUDIO AMPLIFIER].) • Switch the ignition ON (engine off or on) and wait for 5 s or more. • Perform the audio amplifier DTC inspection. (See DTC INSPECTION [AUDIO AMPLIFIER].) • Is the same Pending DTC present?	Yes	Return to Step 1 and inspect for other possible causes. If the malfunction recurs, replace the audio amplifier, then go to the next step. (See AUDIO AMPLIFIER REMOVAL/INSTALLATION.)
4		No	Go to the next step.
5	VERIFY IF OTHER DTCs DISPLAYED • Verify if other DTCs are displayed. • Are any other DTCs displayed?	Yes	Repair the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [AUDIO AMPLIFIER].)
5		No	DTC troubleshooting completed.