CHARGE LID CANNOT BE LOCKED/UNLOCKED [SECURITY AND LOCKS]

id0903k7028700

Outline

Description

•  The Charge lid cannot be locked or unlocked.

Possible cause

•  Connector or terminal malfunction of the following parts:

―  Charge lid lock actuator

―  Charge port-electrical supply unit

•  Short to power supply, short to ground, or open circuit in charge lid lock actuator signal circuit

•  Charge lid lock actuator malfunction

•  Charge port-electrical supply unit

Diagnostic Procedure

Step

Inspection

Results

Action

1

VERIFY ALL SYSTEM DTCs

•  Perform the DTC inspection.
(See DTC INSPECTION.)

•  Are any DTCs displayed?

Yes

Repair the malfunctioning location according to the applicable DTC troubleshooting.

No

Go to the next step.

2

INSPECT CHARGE LID LOCK ACTUATOR AND CHARGE PORT-ELECTRICAL SUPPLY UNIT CONNECTORS FOR MALFUNCTION

•  Inspect the applicable connector and terminal.
(See CONNECTOR INSPECTION.)

•  Are the connector and terminal normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

3

INSPECT CHARGE LID LOCK ACTUATOR SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY, SHORT TO GROUND, AND OPEN CIRCUIT

•  Inspect the signal circuit for a short to power supply, short to ground, and an open circuit.
(See CIRCUIT INSPECTION.)

•  Is the circuit normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

4

INSPECT CHARGE LID LOCK ACTUATOR FOR MALFUNCTION

•  Inspect the applicable part.
(See CHARGE LID LOCK ACTUATOR INSPECTION.)

•  Is the part normal?

Yes

Go to the next step.

No

Repair or replace the malfunctioning location and perform the repair completion verification.

(See CHARGE LID BOX ASSEMBLY REMOVAL/INSTALLATION.)

Repair completion verification

VERIFY THAT VEHICLE IS REPAIRED

•  Install/connect the part removed/disconnected during the troubleshooting procedure.

•  Has the malfunction symptom been eliminated?

Yes

Complete the symptom troubleshooting. (Explain contents of repair to customer)

No

Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error.

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [L.H.D. (E)].)

(See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [R.H.D.].)

If the CAN communication is normal, perform the diagnosis from Step 1.

•  If the malfunction is not resolved, replace the charge port-electrical supply unit.
(See CHARGE PORT-ELECTRICAL SUPPLY UNIT REMOVAL/INSTALLATION.)

Description	• The Charge lid cannot be locked or unlocked.
Possible cause	• Connector or terminal malfunction of the following parts: ― Charge lid lock actuator ― Charge port-electrical supply unit • Short to power supply, short to ground, or open circuit in charge lid lock actuator signal circuit • Charge lid lock actuator malfunction • Charge port-electrical supply unit

Step	Inspection	Results	Action
1	VERIFY ALL SYSTEM DTCs • Perform the DTC inspection. (See DTC INSPECTION.) • Are any DTCs displayed?	Yes	Repair the malfunctioning location according to the applicable DTC troubleshooting.
1		No	Go to the next step.
2	INSPECT CHARGE LID LOCK ACTUATOR AND CHARGE PORT-ELECTRICAL SUPPLY UNIT CONNECTORS FOR MALFUNCTION • Inspect the applicable connector and terminal. (See CONNECTOR INSPECTION.) • Are the connector and terminal normal?	Yes	Go to the next step.
2		No	Repair or replace the malfunctioning location and perform the repair completion verification.
3	INSPECT CHARGE LID LOCK ACTUATOR SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY, SHORT TO GROUND, AND OPEN CIRCUIT • Inspect the signal circuit for a short to power supply, short to ground, and an open circuit. (See CIRCUIT INSPECTION.) • Is the circuit normal?	Yes	Go to the next step.
3		No	Repair or replace the malfunctioning location and perform the repair completion verification.
4	INSPECT CHARGE LID LOCK ACTUATOR FOR MALFUNCTION • Inspect the applicable part. (See CHARGE LID LOCK ACTUATOR INSPECTION.) • Is the part normal?	Yes	Go to the next step.
4		No	Repair or replace the malfunctioning location and perform the repair completion verification. (See CHARGE LID BOX ASSEMBLY REMOVAL/INSTALLATION.)
Repair completion verification	VERIFY THAT VEHICLE IS REPAIRED • Install/connect the part removed/disconnected during the troubleshooting procedure. • Has the malfunction symptom been eliminated?	Yes	Complete the symptom troubleshooting. (Explain contents of repair to customer)
Repair completion verification		No	Refer to the controller area network (CAN) malfunction diagnosis flow to inspect for a CAN communication error. (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [L.H.D. (E)].) (See CONTROLLER AREA NETWORK (CAN) MALFUNCTION DIAGNOSIS FLOW [R.H.D.].) If the CAN communication is normal, perform the diagnosis from Step 1. • If the malfunction is not resolved, replace the charge port-electrical supply unit. (See CHARGE PORT-ELECTRICAL SUPPLY UNIT REMOVAL/INSTALLATION.)