ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)]

id0402b2800200


On-Board Diagnostic (OBD) Test Description

•  The OBD test inspects the integrity and function of the DSC and outputs the results when requested by the specific tests.
•  On-board diagnostic test also:
―  Provides a quick inspection of the DSC usually performed at the start of each diagnostic procedure.
―  Provides verification after repairs to ensure that no other faults occurred during service.
•  The OBD test is divided into 3 tests:
―  Read/clear diagnostic results, PID monitor and record and active command modes.

Read/clear diagnostic results

•  This function allows you to read or clear DTCs in the DSC HU/CM memory.


PID/Data monitor and record

•  This function allows you to access certain data values, input signals, calculated values, and system status information.


Active command modes

•  This function allows you to control devices through the M-MDS.


Reading DTCs Procedure

1.  Connect the M-MDS (IDS) to the DLC-2.

am2zzw00001261

2.  After the vehicle is identified, select the following items from the initialization screen of the IDS.

1.  Select “Self Test”.
2.  Select “Modules”.
3.  Select “ABS”.

3.  Verify the DTC according to the directions on the screen.

•  If any DTCs are displayed, perform troubleshooting according to the corresponding DTC inspection.

4.  After completion of repairs, clear all DTCs stored in the DSC. (See Clearing DTCs Procedures.)


Clearing DTCs Procedures

1.  Connect the M-MDS (IDS) to the DLC-2.

am2zzw00001261

2.  After the vehicle is identified, select the following items from the initialization screen of the IDS.

1.  Select “Self Test”.
2.  Select “Modules”.
3.  Select “ABS”.

3.  Verify the DTC according to the directions on the screen.

4.  Press the clear button on the DTC screen to clear the DTC.

5.  Turn the ignition switch to the LOCK position.

6.  Turn the ignition switch to the ON position and wait for 5 s or more.

7.  Perform DTC inspection. (See Reading DTCs Procedure.)

8.  Verify that no DTCs are displayed.


PID/Data Monitor and Record Procedure

1.  Connect the M-MDS (IDS) to the DLC-2.

am2zzw00001261

2.  After the vehicle is identified, select the following items from the initialization screen of the IDS.

1.  Select “DataLogger”.
2.  Select “Modules”.
3.  Select “ABS”.

3.  Select the applicable PID from the PID table.

4.  Verify the PID data according to the directions on the screen.

Note
•  The PID data screen function is used for monitoring the calculated value of input/output signals in the module.Therefore, if the monitored value of the output parts is not within the specification, it is necessary to inspect the monitored value of input parts corresponding to the applicable output part control. In addition, because the system does not display an output part malfunction as an abnormality in the monitored value, it is necessary to inspect the output parts individually.
•  When detecting DTCs, PIDs related to a malfunctioning system may not display even if the module is normal. Therefore, if a PID is not displayed, it is necessary to verify the DTC, perform malfunction diagnosis of the DTC that was detected, and do repairs.

Active Command Modes Procedure

1.  Connect the M-MDS (IDS) to the DLC-2.

am2zzw00001261

2.  After the vehicle is identified, select the following items from the initialization screen of the IDS.

1.  Select “DataLogger”.
2.  Select “Modules”.
3.  Select “ABS”.

3.  Select the active command modes from the PID table.

4.  Perform the active command modes, inspect the operations for each parts.

•  If the operation of output parts cannot be verified after the active command mode inspection is performed, this could indicate the possibility of an open or short circuit, sticking, or operation malfunction in the output parts.


DTC Table

DTC

System malfunction location

Page

M-MDS
C0001:01
DSC HU/CM internal malfunction (Traction control solenoid valve system)
(See DTC C0001:01/C0002:01/C0003:01/C0004:01/C0010:01/C0011:01/C0014:01/C0015:01/C0018:01/C0019:01/C001C:01/C001D:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0002:01
DSC HU/CM internal malfunction (Traction control solenoid valve system)
C0003:01
DSC HU/CM internal malfunction (Stability control solenoid valve system)
C0004:01
DSC HU/CM internal malfunction (Stability control solenoid valve system)
C0010:01
DSC HU/CM internal malfunction (LF inlet solenoid)
(See DTC C0001:01/C0002:01/C0003:01/C0004:01/C0010:01/C0011:01/C0014:01/C0015:01/C0018:01/C0019:01/C001C:01/C001D:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0011:01
DSC HU/CM internal malfunction (LF outlet solenoid)
C0014:01
DSC HU/CM internal malfunction (RF inlet solenoid)
C0015:01
DSC HU/CM internal malfunction (RF outlet solenoid)
C0018:01
DSC HU/CM internal malfunction (LR inlet solenoid)
C0019:01
DSC HU/CM internal malfunction (LR outlet solenoid)
C001C:01
DSC HU/CM internal malfunction (RR inlet solenoid)
C001D:01
DSC HU/CM internal malfunction (RR outlet solenoid)
C0020:01
Pump motor, motor relay
(See DTC C0020:01/C0020:1C/C0020:71 [DYNAMIC STABILITY CONTROL (DSC)].)
C0020:1C
Pump motor, motor relay
C0020:71
Pump motor, motor relay
C0030:07
LF ABS sensor rotor
(See DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [DYNAMIC STABILITY CONTROL (DSC)].)
C0031:01
LF ABS wheel-speed sensor
(See DTC C0031:01/C0034:01/C0037:01/C003A:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0031:07
LF ABS wheel-speed sensor/ABS sensor rotor
(See DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [DYNAMIC STABILITY CONTROL (DSC)].)
C0033:07
RF ABS sensor rotor
C0034:01
RF ABS wheel-speed sensor
(See DTC C0031:01/C0034:01/C0037:01/C003A:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0034:07
RF ABS wheel-speed sensor/ABS sensor rotor
(See DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [DYNAMIC STABILITY CONTROL (DSC)].)
C0036:07
LR ABS sensor rotor
C0037:01
LR ABS wheel-speed sensor
(See DTC C0031:01/C0034:01/C0037:01/C003A:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0037:07
LR ABS wheel-speed sensor/ABS sensor rotor
(See DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [DYNAMIC STABILITY CONTROL (DSC)].)
C0039:07
RR ABS sensor rotor
C003A:01
RR ABS wheel-speed sensor
(See DTC C0031:01/C0034:01/C0037:01/C003A:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C003A:07
RR ABS wheel-speed sensor/ABS sensor rotor
(See DTC C0030:07/C0031:07/C0033:07/C0034:07/C0036:07/C0037:07/C0039:07/C003A:07 [DYNAMIC STABILITY CONTROL (DSC)].)
C0040:64
Brake switch
(See DTC C0040:64 (MZR 1.3, MZR 1.5) [DYNAMIC STABILITY CONTROL (DSC)].)
(See DTC C0040:64 (MZ-CD 1.6) [DYNAMIC STABILITY CONTROL (DSC)].)
C0044:01
Brake fluid pressure sensor
(See DTC C0044:01/C0044:28/C0044:64 [DYNAMIC STABILITY CONTROL (DSC)].)
C0044:28
Brake fluid pressure sensor
C0044:64
Brake fluid pressure sensor
C0051:28
Abnormal message from EPS control module
(See DTC C0051:28 [DYNAMIC STABILITY CONTROL (DSC)].)
C0061:01
Combined sensor system
(See DTC C0061:01/C0061:28/C0061:64/C0063:01/C0063:28/C0063:64/C006A:16/C006A:17/C1108:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C0061:28
Combined sensor system
C0061:64
Combined sensor system
C0063:01
Combined sensor system
C0063:28
Combined sensor system
C0063:64
Combined sensor system
C006A:04
Combined sensor system
(See DTC C006A:04/C006A:47 [DYNAMIC STABILITY CONTROL (DSC)].)
C006A:16
Combined sensor system
(See DTC C0061:01/C0061:28/C0061:64/C0063:01/C0063:28/C0063:64/C006A:16/C006A:17/C1108:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C006A:17
Combined sensor system
C006A:47
Combined sensor system
(See DTC C006A:04/C006A:47 [DYNAMIC STABILITY CONTROL (DSC)].)
C006B:00
TCS/DSC control system
(See DTC C006B:00/C0072:68 [DYNAMIC STABILITY CONTROL (DSC)].)
C0072:68
TCS/DSC control system
C1108:01
Combined sensor system
(See DTC C0061:01/C0061:28/C0061:64/C0063:01/C0063:28/C0063:64/C006A:16/C006A:17/C1108:01 [DYNAMIC STABILITY CONTROL (DSC)].)
C1109:64
DSC OFF switch
(See DTC C1109:64 [DYNAMIC STABILITY CONTROL (DSC)].)
U0001:88
CAN line
(See DTC U0001:88/U0100:00/U0126:00/U0155:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U0100:00
CAN line
U0125:00
Combined sensor system (CAN2 line malfunction)
(See DTC U0125:00/U0125:88 [DYNAMIC STABILITY CONTROL (DSC)].)
U0125:88
Combined sensor system (CAN2 line malfunction)
U0126:00
CAN line
(See DTC U0001:88/U0100:00/U0126:00/U0155:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U0155:00
CAN line
U0401:68
Signal error from PCM
(See DTC U0401:68 [DYNAMIC STABILITY CONTROL (DSC)].)
U0428:00
Abnormal message from EPS control module
(See DTC U0428:00/U0428:64/U0428:68 [DYNAMIC STABILITY CONTROL (DSC)].)
U0428:64
Abnormal message from EPS control module
U0428:68
Abnormal message from EPS control module
U2100:00
Configuration data not recorded
(See DTC U2100:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U2101:00
Signal error from instrument cluster
(See DTC U2101:00 [DYNAMIC STABILITY CONTROL (DSC)].)
U3000:47
DSC CM (internal malfunction)
(See DTC U3000:47/U3000:48/U3000:49 [DYNAMIC STABILITY CONTROL (DSC)].)
U3000:48
DSC CM (internal malfunction)
U3000:49
DSC CM (internal malfunction)
U3000:54
Combined sensor system (unperformed initialization procedure)
(See DTC U3000:54 [DYNAMIC STABILITY CONTROL (DSC)].)
U3003:16
Power supply system
(See DTC U3003:16/U3003:17 [DYNAMIC STABILITY CONTROL (DSC)].)
U3003:17
Power supply system


PID/DATA Monitor Table

PID name (definition)

Unit/Condition

Operation condition (reference)

Action
BRAKE_SW
Off/On
•  Brake pedal released: Off
•  Brake pedal depressed: On
Inspect the brake switch.
(See BRAKE SWITCH INSPECTION [MTX].)
(See BRAKE SWITCH INSPECTION [ATX, CVT].)
DSC_SW
Off/On
•  DSC OFF switch is released: Off
•  DSC OFF switch is depressed: On
Inspect the DSC OFF switch.
(See DSC OFF SWITCH INSPECTION.)
LAT_ACCL
G
•  Vehicle stopped or driving at constant speed: 0 G
•  Cornering to right: Changes 0 G—positive
•  Cornering to left: Changes 0 G—negative
Inspect the combined sensor.
(See COMBINED SENSOR INSPECTION.)
MCYLI P
Pa, psi
•  Brake pedal depressed: Changes according to the brake fluid pressure
Inspect the brake fluid pressure sensor.
(See BRAKE FLUID PRESSURE SENSOR INSPECTION.)
PMP_MTR
Note
•  Displays in the M-MDS but it does not operate.
STEER_ANGL
°
•  Steering wheel in neutral position (not turned): 0°
•  Steering wheel turned to left: Changes 0°—negative
•  Steering wheel turned to right: Changes 0°—positive
Inspect the EPS control module.
(See EPS CONTROL MODULE INSPECTION.)
VSPD
KPH, MPH
•  Vehicle stopped: 0 KPH, 0 MPH
•  Vehicle running: Vehicle speed
Inspect the DSC HU/CM.
(See DSC SYSTEM INSPECTION.)
Inspect the ABS wheel-speed sensor.
(See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.)
(See REAR ABS WHEEL-SPEED SENSOR INSPECTION.)
VPWR
V
•  Ignition switch at ON: Approx. 12.2 V
•  Idling: Approx. 14.1 V
Inspect power supply circuit.
(See DSC HU/CM INSPECTION.)
V_LF_INL
Off/On
•  Solenoid valve not activated: Off
•  Solenoid valve activated: On
Inspect the DSC HU/CM.
(See DSC SYSTEM INSPECTION.)
V_LF_OTL
Off/On
•  Solenoid valve not activated: Off
•  Solenoid valve activated: On
V_LR_INL
Off/On
•  Solenoid valve not activated: Off
•  Solenoid valve activated: On
V_LR_OTL
Off/On
•  Solenoid valve not activated: Off
•  Solenoid valve activated: On
V_RF_INL
Off/On
•  Solenoid valve not activated: Off
•  Solenoid valve activated: On
V_RF_OTL
Off/On
•  Solenoid valve not activated: Off
•  Solenoid valve activated: On
V_RR_INL
Off/On
•  Solenoid valve not activated: Off
•  Solenoid valve activated: On
V_RR_OTL
Off/On
•  Solenoid valve not activated: Off
•  Solenoid valve activated: On
V_STB_L
Note
•  Displays in the M-MDS but it does not operate.
V_STB_R
V_TRC_L
Note
•  Displays in the M-MDS but it does not operate.
V_TRC_R
YAW_RATE
°/s
•  Vehicle stopped or driving straight: 0 °/s
•  Cornering to left: Changes 0 °/s—negative
•  Cornering to right: Changes 0 °/s—positive
Inspect the combined sensor.
(See COMBINED SENSOR INSPECTION.)
WSPD_LF
KPH, MPH
•  Vehicle stopped: 0 KPH, 0 MPH
•  Vehicle running: Vehicle speed
Inspect the ABS wheel-speed sensor.
(See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.)
WSPD_LR
KPH, MPH
•  Vehicle stopped: 0 KPH, 0 MPH
•  Vehicle running: Vehicle speed
Inspect the ABS wheel-speed sensor.
(See REAR ABS WHEEL-SPEED SENSOR INSPECTION.)
WSPD_RF
KPH, MPH
•  Vehicle stopped: 0 KPH, 0 MPH
•  Vehicle running: Vehicle speed
Inspect the ABS wheel-speed sensor.
(See FRONT ABS WHEEL-SPEED SENSOR INSPECTION.)
WSPD_RR
KPH, MPH
•  Vehicle stopped: 0 KPH, 0 MPH
•  Vehicle running: Vehicle speed
Inspect the ABS wheel-speed sensor.
(See REAR ABS WHEEL-SPEED SENSOR INSPECTION.)


Active Command Modes Table

Command name

Output part

Operation

Operating condition
PMP_MTR
Pump motor
Off/On
Ignition switch at ON
V_LF_INL
LF inlet solenoid valve
V_LF_OTL
LF outlet solenoid valve
V_LR_INL
LR inlet solenoid valve
V_LR_OTL
LR outlet solenoid valve
V_RF_INL
RF inlet solenoid valve
V_RF_OTL
RF outlet solenoid valve
V_RR_INL
RR inlet solenoid valve
V_RR_OTL
RR outlet solenoid valve
V_STB_L
Left stability control solenoid valve
V_STB_R
Right stability control solenoid valve
V_TRC_L
Left traction control solenoid valve
V_TRC_R
Right traction control solenoid valve