DTC P0766

id050200809000

DTC P0766

Shift solenoid D stuck off

DETECTION CONDITION

• When any of DTC P0731, P0732, and P0733 not output (correct judgment), and all conditions below are satisfied.
- ATF temperature 20 °C {68 °F} or more
- Driving in 4GR at D range
- Engine running
- Turbine speed within 225-4,987 rpm
- Differential gear case (output) revolution speed 35 rpm or more
- Vehicle speed 50 km/h {31 mph} or more (ZY, Z6)
- Vehicle speed 35 km/h {22 mph} or more (LF, L3)
- Throttle opening angle at closed throttle position
- Revolution ratio of forward clutch drum revolution to differential gear case revolution below 0.6 or 1.249 or more
- None of the following present: DTC P0500, P0706, P0707, P0708, P0712, P0713, P0715, P0751, P0752, P0753, P0756, P0757, P0758, P0761, P0762, P0763, P0766, P0767, P0767, P0768, P0771, P0772, P0773
Diagnostic support note:
• This is a continuous monitor (CCM).
• The MIL illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.
• The PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle.
• FREEZE FRAME DATA is available.
• The AT warning light illuminates.
• The DTC is stored in the PCM memory.

POSSIBLE CAUSE

• ATF level low
• Deteriorated ATF
• Shift solenoid D stuck
• Control valve stuck
• PCM malfunction

Diagnostic procedure

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA HAS BEEN RECORDED

• Has the FREEZE FRAME DATA been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2

VERIFY RELATED REPAIR INFORMATION AVAILABILITY

• Verify related Service Bulletins and or/on-line repair information availability.
• Is any related repair information available?
Yes
Perform repair or diagnosis according to the available repair information.
• If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3

INSPECT ATF CONDITION

• Turn the ignition switch to the LOCK position.
• Inspect the ATF condition.
- Clear red: Normal
- Milky: Water mixed in fluid
- Reddish brown: Deteriorated ATF
• Is it normal?
Yes
Go to the next step.
No
If the ATF color is milky or reddish brown, replace ATF, then go to Step 5.
4

INSPECT ATF LEVEL

• Start the engine.
• Warm up the ATX.
• Is the ATF level within the specification?
Yes
Go to the next step.
No
Add ATF to the specified level, then go to Step 7.
5

INSPECT LINE PRESSURE

• Start the engine.
• Measure the line pressure.

Specification

Idle:

330-470 kPa {3.4-4.7 kgf/cm2, 48-68 psi}

 

Stall:

ZY: 950-1,110 kPa {9.7-11.3 kgf/cm2, 138-160 psi}

Z6: 1,080-1,270 kPa {11.1-12.9 kgf/cm2, 157-184 psi}

LF: 1,140-1,320 kPa {11.7-13.4 kgf/cm2, 166-191 psi}

L3: 1,160-1,320 kPa {11.9-13.4 kgf/cm2, 170-191 psi}

• Are the line pressures within the specifications?
Yes
Go to the next step.
No
• All ranges: Replace the oil pump or control valve body, then go to Step 7.
• Any ranges: Replace the ATX, then go to Step 7.
(See ATX Workshop Manual FN4A-EL.)
6

INSPECT OPERATION OF EACH VALVE AND EACH SPRING

• Turn the ignition switch to the LOCK position.
• Remove the control valve body.
• Disassemble the control valve body.
• Is each valve operation normal and is the return spring normal?
(See ATX Workshop Manual FN4A-EL.)
Yes
Replace the ATX, then go to the next step.
(See ATX Workshop Manual FN4A-EL.)
No
Repair or replace the shift valve and return spring, then go to the next step.
(See ATX Workshop Manual FN4A-EL.)
7

VERIFY TROUBLESHOOTING OF DTC P0766 COMPLETED

• Make sure to reconnect all the disconnected connectors.
• Clear the DTC from the memory using the WDS or equivalent.
• Start the engine.
• Warm up the ATX.
• Drive the vehicle under the following conditions and make sure that gears shift smoothly from 1GR to 4GR:
- ATF temperature: 20 °C {68 °F} or more
- Drive in the D range
- Throttle opening angle (TP PID): 0% (4GR only)
- Vehicle speed (VSS PID): 50 km/h {31 mph} or more. (4GR only) (ZY, Z6)
- Vehicle speed (VSS PID): 35 km/h {22 mph} or more. (4GR only) (LF, L3)
• Is the PENDING CODE present?
Yes
Replace the PCM, then go to the next step.
No
Go to the next step.
8
VERIFY AFTER REPAIR PROCEDURE
• Perform the "After Repair Procedure".
• Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE.)
No
DTC troubleshooting completed.