Installation
INTERIOR PANELS / TRIM: LOWER INSTRUMENT PANEL: INSTALLATION
1. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(a) When using a new lower instrument panel sub-assembly:
(1) Immediately before installing the lower instrument panel sub-assembly, twist and cut off the portion shown in the illustration.
(b) Install the lower instrument panel sub-assembly with the 2 bolts [A], 10 screws [C] and screw [D].
(c) Engage the 2 claws.
(d) Engage the 2 claws to connect the room temperature sensor.
(e) Engage each clamp.
(f) Connect the connector and engage the claw as shown in the illustration.
NOTICE:
Be sure to engage the connector securely.
(g) Connect the connector.
2. INSTALL ANTENNA CORD SUB-ASSEMBLY (w/o Satellite Radio) Installation
3. INSTALL ANTENNA CORD SUB-ASSEMBLY (w/ Satellite Radio) Installation
4. INSTALL GLOVE BOX LIGHT ASSEMBLY Installation
5. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
(a) Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
6. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY Installation
7. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
(a) Connect each connector.
(b) Engage each clamp.
(c) Engage the guide and 2 claws.
(d) Install the No. 1 instrument panel under cover sub-assembly with the 2 screws [E].
8. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH Installation
9. INSTALL FRONT DOOR SCUFF PLATE LH Installation
10. INSTALL SHIFT LOCK CONTROL UNIT ASSEMBLY Installation
11. INSTALL AIR CONDITIONING CONTROL ASSEMBLY Installation
12. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
(a) Connect each connector.
(b) Engage the clamp.
(c) Engage the 11 claws to install the lower instrument finish panel sub-assembly.
13. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type) Installation
14. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for Navigation Receiver Type) Installation
15. INSTALL COMBINATION METER ASSEMBLY
(a) Connect each connector.
(b) Engage the clamp.
(c) Install the combination meter assembly with the 4 screws [C].
16. INSTALL CONSOLE BOX ASSEMBLY Installation
17. INSTALL FRONT NO. 2 CONSOLE BOX INSERT Installation
18. INSTALL LOWER CONSOLE BOX POCKET Installation
19. INSTALL NO. 1 CONSOLE BOX SHEET Installation
20. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY Installation
21. INSTALL CENTER FLOOR CARPET COVER LH
(a) Engage the guide and 4 claws to install the center floor carpet cover LH as shown in the illustration.
22. INSTALL CENTER FLOOR CARPET COVER RH
(a) Engage the guide and 4 claws to install the center floor carpet cover RH as shown in the illustration.
23. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
(a) Engage the claw to install the glove compartment door stopper sub-assembly.
24. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
(a) With the glove compartment door assembly opened approximately 55° from its closed position, engage the 2 hinges horizontally.
NOTICE:
Engaging the hinges from the top will deform the hinges. Be sure to install the glove compartment door assembly horizontally.
Text in Illustration
(b) Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the glove compartment door assembly.
Text in Illustration
(c) Engage the claw and connect the glove compartment door stopper sub-assembly.
25. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
(a) Connect each connector.
(b) Engage the guide and 3 claws to install the No. 2 instrument panel under cover sub-assembly.
26. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT
Use the same procedure as for the LH side Installation
27. INSTALL FRONT DOOR SCUFF PLATE RH
HINT
Use the same procedure as for the LH side Installation
28. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY
Installation
29. INSPECT SHIFT LEVER OPERATION Installation